Steering Kit - 1ASFK03621

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Quantity:   3 Piece Set
  • Kit Includes:
      (2) Front Outer Tie Rods
      (1) Power Rack & Pinion Assembly


  • Brand New Steering Rack & Tie Rod Kit
  • New Power Rack & Pinion Assembly
    • not remanufactured, no core charge
  • Rack includes gear assembly, inner tie rods, & rack boots
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (1:09)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands onto the unibody frame rail at the front and ahead the lower control arm at the rear
    • Secure the vehicle levelly on both side
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (3:57)
    • Turn the wheel by hand to check for play in the tie rod
    • Measure the distance from the steering rack bellow to the lock nut
    • Record this measurement
    • Alternatively, mark the inner tie rod threads against the lock nut with a marker
    • Straighten out the cotter pin with needle nose pliers
    • Pull the cotter pin out of the castle nut
    • Loosen the castle nut from the tie rod with a 17mm socket and ratchet
    • Apply penetrating oil to the lock nut
    • Loosen the lock nut with a 22mm wrench
    • Tap the tie rod loose from the spindle with a hammer
    • Remove the castle nut
    • Tap the tie rod out of the spindle
  3. step : Removing the Power Steering Lines and Aligning the Steering Wheel (6:56)
    • Have a drain pan ready
    • Remove the power steering lines with a 17mm wrench
    • Remove the 12mm pinch-bolt attached to the intermediate steering shaft
    • Turn the key to the on position
    • Move the steering wheel to the lock on one side
    • Count each full rotation and spin it back 1.5 turns
    • Pry the steering shaft off the splines with a flat blade screwdriver
  4. step : Removing the End Links (10:46)
    • Remove the 17mm nut with vise grips and a socket and ratchet
    • Remove the link from the end of the strut
    • Repeat the steps on the other side
  5. step : Removing the Steering Rack (11:33)
    • Remove the two 13mm bolts securing the rack in place
    • Remove the bolt from the rack
    • Repeat the steps on the other side
    • Remove the 12mm nut on the top of the steering rack clamp
    • Lift up and remove the line from the stud
    • Lift up and remove the rack from its seats in the subframe
    • Remove the steering rack
  6. step : Preparing the Steering Rack (16:06)
    • Remove the brackets over to the new rack
    • Slice the rubber collar with a blade
    • Transfer the collar and bracket to the new steering rack
    • Bend the bracket back into place with pliers
    • Bend the tabs into place with a second pair to lock the bracket
    • Loosen the plastic caps out of the new rack with a flat blade screwdriver
    • Turn the splines all the way one direction, and turn it back halfway to center it
  7. step : Installing the Steering Rack (21:13)
    • Insert the steering rack into its channels without pushing from the tie rod ends
    • Tighten the 13mm bolts to the steering rack
    • Tighten the top and then the bottom power steering line
    • Tighten the 12mm nut to the top of the steering rack clamp
  8. step : Reinstalling the End Link (26:34)
    • Lift the end link up into place
    • Tighten the 17mm nut to the end link with vise grips and a ratchet and socket
  9. step : Reinstalling the Outer Tie Rod (27:26)
    • If you marked the inner tie rod, spin the lock nut to match the paint line
    • If you took a measurement, spin the lock nut to the correct distance from the steering bellow
    • Spin the outer tie rod onto the inner tie rod until it reaches the lock nut
    • Push the tie rod stud into the wheel spindle
    • Torque the tie rod nut to 36 foot-pounds
    • Install the new cotter pin with the longer leg facing down
    • Bend the cotter pin under the nut with pliers
    • Turn the inner tie rod with a 14mm wrench if it needs to be adjusted
    • Hold the inner tie rod with a 14mm wrench
    • Tighten the lock nut with a 22mm wrench
  10. step : Reattaching the Wheel (30:16)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  11. step : Bleeding the Power Steering (30:35)
    • Secure the vehicle on jack stands again
    • Fill the reservoir with the appropriate fluid
    • Turn the wheel all the way to the lock position on one side
    • Turn the wheel all the way to the lock position on the other side
    • Repeat this process a few times
    • Start the engine
    • Turn the wheel from lock to lock with the engine running
    • After a few trials, lower the vehicle to the ground
    • Repeat this process until there is no whining sound
    • Turn the engine off
    • Top off the power steering fluid
    • Wipe off any power steering fluid in the engine bay
    • Twist on power steering fluid reservoir cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Measuring Tape
  • Hammer
  • Drain Pan
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers
  • Vise Grip Pliers
  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 17mm Socket
  • 14mm Socket
  • 12mm Socket
  • 22mm Socket

  • Specialty Tools

  • Vise-Grips

  • Wrenches - Metric

  • 22mm Wrench
  • 14mm Wrench
  • 19mm Wrench
  • 12mm Wrench

5.00/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Great product I will be doing more shopping in the future with this company
March 29, 2017
Qaulity part
Awesome part fitted just perfect very well put together would recommend this to anyone
August 6, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1997-2000Lexus ES300 Lexus ES300 Steering Kit 3 Piece Set
1995-2004Toyota Avalon Toyota Avalon Steering Kit 3 Piece Set
1992-2000Toyota Camry Toyota Camry Steering Kit 3 Piece Set
2001Toyota Camry Toyota Camry Steering Kit 3 Piece Set (Built Before 7/01 Production Date)
Part #: 1ASFK03621

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(34:40 min)