Specifications:

  • Includes both LH (Driver Side) & RH (Passenger Side) FRONT
  • Direct replacements
  • Built to strict quality control standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:30)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads and Rotor (1:00)
    • Remove 13mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
  3. step : Preparing the New Brake Pads and Caliper (2:39)
    • Remove the brake pad brackets
    • Remove the caliper boot slides
    • Clean the caliper bracket with a wire brush
    • Apply grease to the new caliper slides
    • Insert the slides into the caliper
    • Press on the new brake pad brackets
    • Apply grease to the brake pad slides
    • Pry out the old clip from the caliper with a flat blade screwdriver
    • Press on the clip to the caliper bracket
  4. step : Installing the New Brake Pads (8:51)
    • Put the caliper bracket back into place
    • Start the bolts by hand
    • Tighten the bolts to 136 foot-pounds of torque
    • Apply grease to the brake pad tabs
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread bolts by hand
    • Tighten bolts to 21-26 foot-pounds
    • Clean the rotor with brake parts cleaner or mineral spirits
  5. step : Reattaching the Wheel (12:15)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 83-112 foot-pounds in a crossing or star pattern
  6. step : Testing the Brakes (12:54)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    Drills, Drill Bits & Related

  • Drill Bit Set

  • General Tools

  • Large C-Clamp
  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Brake Parts Cleaner
  • Safety Glasses
  • Paper Towels
  • Bungee Cord
  • Anti-Seize Grease

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 19mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1995-2001 Ford Explorer Front Caliper Hardware Kit
  • 2004 Ford F150 Heritage Truck Front Caliper Hardware Kit
  • 1997-1998 Ford F150 Truck Front Caliper Hardware Kit
  • 1999-2003 Ford F150 Truck Front Caliper Hardware Kit for Models with 5 Lug Wheels (excluding Lightning Models)
  • 1995-2002 Ford Ranger Front Caliper Hardware Kit
  • 2002 Lincoln Blackwood Front Caliper Hardware Kit
  • 1995-1997 Mazda B2300 Truck Front Caliper Hardware Kit
  • 2001-2002 Mazda B2300 Truck Front Caliper Hardware Kit
  • 1998-2001 Mazda B2500 Truck Front Caliper Hardware Kit
  • 1995-1996 Mazda B3000 Truck Front Caliper Hardware Kit
  • 1998-2002 Mazda B3000 Truck Front Caliper Hardware Kit
  • 1995-2002 Mazda B4000 Truck Front Caliper Hardware Kit
  • 1997-2001 Mercury Mountaineer Front Caliper Hardware Kit
Part #: 1ABRX00037

Out of Stock

How-to Video:

(13:09 min)