Our windshield washer reservoirs are some of the highest quality replacements on the market!


  • Brand New Windshield Washer Reservoir
  • Includes Cap
  • Direct replacement
  • Built to strict quality control standards
  • Washer pump not included

Now you can buy a high quality windshield washer reservoir that is built to strict quality control standards. Replace your broken or cracked one now with this great fitting washer tank.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Auxiliary Battery Tray (0:25)
    • Remove the eight 10mm bolts from the auxiliary battery tray
    • Lift the battery tray up and out
    • Remove the 10mm bolt from the top of the washer bottle
  2. step : Loosening the Fender Liner (1:24)
    • Remove the 7mm bolts from the fender liner
    • Pry out the barbed clips in the liner with a flat blade screwdriver
    • Peel back the fender liner to access the bulbs
  3. step : Removing the Washer Bottle (2:58)
    • Have a drain pan ready
    • Disconnect the sensor wiring harness
    • Remove the 10mm bolt from the bottom of the washer tank
    • Disconnect the electrical connectors
    • Remove the hoses from the washer bottle
    • Let the bottle drain
  4. step : Removing the Washer Sensor (5:03)
    • Pry the sensor out and pop it off the bottle
    • Remove the rubber grommet
    • Remove the float from the bottle
  5. step : Removing the Washer Pump (6:09)
    • Pry the pumps back and forth out of the washer bottle
  6. step : Installing the Washer Pump (6:35)
    • Press the pumps into the washer bottle
  7. step : Installing the Washer Sensor (7:03)
    • Insert the float to the new sensor
    • Insert the grommet to the hole
    • Press the sensor into the washer bottle
  8. step : Installing the Washer Bottle (7:24)
    • Transfer the nutsert over from the old bottle to the new one
    • Connect the hoses into the grooves on the bottle and the fittings on the pump
    • Connect the motor connector
    • Insert the bottle into place
    • Tighten the 10mm bolt to the bottle
    • Connect the sensor wiring harness
  9. step : Reinstalling the Fender Liner (10:12)
    • Press in the clips to the fender liner
    • Tighten the 7mm bolts to the liner
  10. step : Installing the Auxiliary Battery Tray (11:21)
    • Tighten the 10mm bolt to the top of the water bottle
    • Reinstall the battery tray
    • Tighten the eight 10mm bolts to the tray
  11. step : Refilling the Washer Fluid (12:18)
    • Open the cap
    • Pour the washer fluid into the neck until the fill line

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Windshield Washer Fluid

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2007-2014 Cadillac Escalade Windshield Washer Reservoir
  • 2007-2014 Cadillac Escalade ESV Windshield Washer Reservoir
  • 2007-2014 Chevy Suburban 1500 Windshield Washer Reservoir
  • 2007-2014 Chevy Suburban 2500 Windshield Washer Reservoir
  • 2007-2014 Chevy Tahoe Windshield Washer Reservoir
  • 2007-2014 GMC Yukon Windshield Washer Reservoir
  • 2007-2013 GMC Yukon XL 1500 Windshield Washer Reservoir
  • 2007-2013 GMC Yukon XL 2500 Windshield Washer Reservoir

This part replaces:

  • Dorman 603-177
  • OE # 15942522
  • OE # 20999340
  • OE # 10382707
Part #: 1AWWR00153

How-to Video:

(12:40 min)