Replaces

Wheel Bearing & Hub Assembly Front Pair Timken SP550207 - TKSHS00409

Part Details

  • Quantity: Pair
  • Front or Rear Location: Front

TIMKEN WHEEL BEARING & HUB ASSEMBLIES: SP550207

These replacement hub & bearing assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 4 Bolt Rectangular Flange
  • Fits 6 Lug Wheel
  • Replaces dealer part number: 7L3Z-1104-A, 7L3Z1104A
  • Has ABS (Anti Lock Brakes) sensor already installed
  • Direct replacement
  • Built to strict quality control standards
  • Fits 4WD (Four Wheel Drive) Models only

Note: For 2005 models you can find the production date of your vehicle on either the outer edge of the driver's front door or on the latch piller that the door closes on.

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:42)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Remove the hub cap with pliers
    • Loosen the 13mm nut
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:32)
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove the 13mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (2:32)
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Thread a nut onto the rotor
    • Hit the rotor with a hammer
    • Pull the rotor off
  4. step : Removing the Hub (2:58)
    • Disconnect the ABS harness sensor
    • Remove the ABS from the harness on the bracket
    • Remove the four 18mm bolts from the hub
    • Remove the 13mm hub nut, making sure you can push the nut in and out
    • Twist in an 18mm bolt to the hub
    • Remove the hub
  5. step : Installing the Hub (4:42)
    • Grease the set of bearings inside the new hub with bearing grease
    • Apply a light coat of bearing grease to the engaging wheel for the 4WD
    • Insert the hub into place
    • Tighten the 18mm bolts to the hub
    • Tighten the 18mm bolts to 95 foot-pounds of torque
    • Replace and tighten the 13mm hub nut
    • Tighten the 13mm bolt to 20 foot-pounds of torque
    • Push the ABS wire into its respective brackets
    • Replace the hub cap
  6. step : Installing the New Brake Rotor (6:41)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Adjust the emergency brake, if necessary
    • Put the bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts to 95 foot-pounds of torque
  7. step : Installing the New Brake Pads (7:24)
    • Put the caliper on
    • Thread the 13mm bolts by hand
    • Tighten bolts to 25 foot-pounds
    • Remove the lug nut from the rotor
  8. step : Reattaching the Wheel (8:55)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Connect the ABS sensor
  9. step : Testing the Brakes (9:42)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • A Piece of Pipe (for leverage)
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 21mm Socket
  • 18mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Do you grease new front wheel 4/4 hub?
John R on Mar 30, 2017
BEST ANSWER: Our bearings will be pregreased, however if you choose you may take a needle grease and apply more.

Vehicle Fit

Year Make Model Description
2005Ford F150 Truck Ford F150 Truck 4 Wheel Drive Front for Models with 6 Lug Wheels Wheel Bearing & Hub Assembly Pair (Built After 11/28/04 Production Date) Timken SP550207
2006-2008Ford F150 Truck Ford F150 Truck 4 Wheel Drive Front for Models with 6 Lug Wheels Wheel Bearing & Hub Assembly Pair Timken SP550207
2006-2008Lincoln Mark LT Lincoln Mark LT 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken SP550207

This part replaces:

  • Timken SP550207
Only 3 left in stock
Part #: TKSHS00409


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: SP550207

How-to Video:

(10:13 min)