Replaces

Volvo Wheel Bearing & Hub Assembly Front Pair Timken HA594181 - TKSHS00369

TIMKEN WHEEL BEARING & HUB ASSEMBLIES: HA594181

These replacement hub & bearing assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part number: 274378-9, 2743789
  • Direct replacements
  • Built to strict quality control standards
  • Fit 5 Lug Wheels

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Part Details

  • Front or Rear Location: Front
  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the wheel (1:30)
    • Loosen the lug nuts and the hub nut.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Disassemble the brakes (2:15)
    • Unbolt the calipers using a T47 Torx bit and ratchet.
    • Compress your caliper using a flat blade screwdriver and remove it.
    • Use wire ties to secure the caliper up and out of the way.
    • Remove the caliper bracket by unbolting the two 15 mm bolts.
    • Pull the brake disc/rotor
  3. step : Loosen or remove the strut (5:10)
    • You want to move the strut out of the way.
    • Loosen or remove the top 13 mm nuts.
    • Apply penetrating oil on the nuts and bolts involved.
    • Disconnect the stabilizer link from the strut
    • Use your 17 mm socket to remove the stabilizer link from the strut.
    • Apply penetrating oil to the bottom 18 mm bolts and use a breaker bar or pipe to help break them loose.
    • Unclip the ABS sensor wiring from the strut.
    • Use a hammer to work the bottom bolts.
    • Either push the strut to the side or remove it completely, depending on whether you’d rather work around it or have it completely out of your way.
  4. step : Remove the axle (8:05)
    • Remove the hub nut with your 35 mm socket
    • Use a hammer and extension to push the axle out of the hub
    • Unbolt the axle on the transmission end with a 12 mm socket and ratchet and penetrating oil.
    • Pull the axle out using a pry bar.
    • Take care not to damage the CV joint
  5. step : Remove the hub (8:50)
    • If you didn't remove the strut, replace the 18 mm bolts to connect the steering knuckle and strut to help hold the steering knuckle at an angle.
    • Use your E14 Star Torx Bit and a ratchet to unbolt the hub.
    • Clean the steering knuckle with a wire brush.
    • Install the hub and torque the bolts to 70 ft lbs.
    • Rotate between the four hub bolts to torque them evenly.
  6. step : Reinstall the axle (11:20)
    • Work the axle back into the steering knuckle and transmission.
    • Bolt the axle in and torque the 12 mm bolts to 35 ft lbs
  7. step : Reinstall the strut (12:05)
    • Insert the strut into place and bolt the 13 mm nuts down and torque to 20-30 ft lbs.
    • Replace the stabilizer link and tighten the 17 mm bolt.
    • Torque the 18 mm bolts to 65-70 ft lbs.
  8. step : Re-assemble the brakes (13:40)
    • Replace the brake rotor
    • Replace the hub nut.
    • Install the caliper bracket and torque the 15 mm bolts to 70 ft lbs.
    • Put the brake pads into place and install the calipers.
    • Tighten the caliper bolts to 25-30 ft lbs.
  9. step : Replace the wheel (14:30)
    • Put the wheel on and hand tighten the lug nuts.
    • Lower the vehicle.
    • If your vehicle the small hub bolts, tighten to 33 ft lbs, if it uses a large nut, torque to 89 ft lbs plus an additional third of a turn.
    • Torque the lug nuts to 100 ft lbs.
    • Pump the brakes before road testing to recompress your caliper pistons.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar
  • Torque Wrench
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 11mm Socket
  • 10mm Socket
  • 15mm Socket
  • 13mm Socket
  • 18mm Socket
  • 19mm Socket
  • 12mm Socket
  • 14mm Socket
  • 17mm Socket
  • 16mm Socket

  • Torx Drivers & Sockets

  • T47 Torx Socket
  • E14 Inverted Socket

  • Wrenches - Metric

  • 11mm Wrench
  • 19mm Wrench
  • 14mm Wrench
  • 13mm Wrench
  • 12mm Wrench
  • 10mm Wrench
  • 17mm Wrench
  • 18mm Wrench
  • 15mm Wrench
  • 16mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1994-1997Volvo 850 Volvo 850 Front for Models with 5 Lug Wheels Wheel Bearing & Hub Assembly Pair Timken HA594181
1998Volvo C70 Volvo C70 Front Wheel Bearing & Hub Assembly Pair Timken HA594181
1998Volvo S70 Volvo S70 Front Wheel Bearing & Hub Assembly Pair Timken HA594181
1998Volvo V70 Volvo V70 Front Wheel Bearing & Hub Assembly Pair Timken HA594181

This part replaces:

  • Timken HA594181
Part #: TKSHS00369

Out of Stock

Timken
Brand #: HA594181

How-to Video:

(15:57 min)