This replacement Tail light is just what you need to get your vehicle in good looking form again!

This tail lamp features the following specifications:

  • RH (Passenger Side) INNER
    • Mounts on trunk lid
  • Replaces dealer part numbers: 1HM 945 108, 1HM945108
  • Includes lens & Housing
  • DOT (Department of Transportation) & SAE (Society of Automotive Engineers) approved
  • Direct replacement
  • Correct for GL, GLS, & GT Models
    • Has amber top lens & red bottom lens
  • Will fit GLX & K2 Models, but look cosmetically different

This tail light makes a great replacement and has good cost savings over a dealer unit.

 

 

Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Light uses same wiring as the original assembly, providing easy, trouble-free installation.  No cutting or splicing required.

DOT and SAE Compliant

DOT & SAE compliant: meets federal regulations for on-road use

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

  1. step : Remove the tail light assembly (0:55)
    • Open the trunk
    • Peel back the trunk liner by removing four push clips.
    • Use your screwdriver to pry out the center of the clips to remove them.
    • Service the bulbs by unclipping the bracket holding the bulbs into the assembly and unplugging the bulbs
    • Unbolt the tail light assembly with an 8 mm socket and ratchet to remove the three nuts.
    • Remove your license plate and remove the four screws anchoring the plastic vanity piece behind the plate.
    • Unbolt the four nuts securing the tail lights to the vanity piece.
    • Pull the tail light assembly out.
  2. step : Install the new tail lights (6:33)
    • Secure the new tail lights to the plastic vanity piece with your 8 mm socket and ratchet.
    • Bolt the whole assembly back onto the car.
    • Plug in the bulbs and wiring harness bracket back into the tail lights.
    • Secure all six of the nuts securing the tail lights to the trunk.
    • Bolt the tail light assembly into place using your 8 mm socket and ratchet.
    • make sure your wiring harness and bulbs are all connected.
    • Replace the license plate.
    • Clip the trunk liner back into place and close the trunk.
    • Close the trunk and enjoy your new 1A Auto tail lights.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1993-1998 VW Jetta GL Inner Tail Light Passenger Side
  • 1993-1998 VW Jetta GLS Inner Tail Light Passenger Side
  • 1993-1998 VW Jetta GT Inner Tail Light Passenger Side
  • 1999 VW Jetta GL Inner Tail Light Passenger Side (8th Vin Digit H)
  • 1999 VW Jetta GLS Inner Tail Light Passenger Side (8th Vin Digit H)

This part replaces:

  • Partslink VW2801112
  • Hollander 166-58643AR
  • OE # 1HM 945 108
  • DEPO 441-1302R-UQ
Only 1 left in stock
Part #: 1ALTL01425

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(09:31 min)