Specifications

  • Fits LH (Driver Side)
  • Replaces dealer part number: F2TZ-13008-B, F2TZ13008B
  • Includes lens, housing, and adjusting screws
  • Bulbs not included
This headlight is a great replacement and has good cost savings over a headlight from the dealer.
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Part Details

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly..

    Note: DO NOT TOUCH the bulbs- the oil from your fingers will burn into the light and foul your bulb. Clean with rubbing alcohol and a soft cloth if the bulbs do get touched.

  1. step : To replace just the headlight bulbs (0:45)
    • Pop the hood and secure it.
    • Reach behind the headlight assembly.
    • Remove and replace the bulb.
  2. step : Remove the parking light assembly (1:50)
    • Use a 10mm deep socket to remove the bolt and the three nuts securing the parking light assembly
    • Remove the two Phillips screws at the top of the headlight trim panel
    • Pull the parking light out.
    • Unplug the wiring harness and bulbs.
  3. step : Remove the headlight assembly (3:20)
    • Use a pair of needle nose pliers or a bent tipped awl to unclip the three clips securing the headlight assembly
    • pull out and unplug the wiring harness and bulbs
  4. step : Aim headlights (4:55)
    • Adjust the adjustor bolts to match the old headlight assembly for a preliminary aim.
  5. step : install the headlight assembly (5:45)
    • Plug in the bulbs and harness
    • Seat the headlight assembly and clip it in
  6. step : Reassemble the parking light assembly (8:00)
    • You put the trim back in place with the parking and marker lights.
    • Make sure you reconnect the two side marker lights first, and then you can reconnect the larger parking light from the back, and then put the trim into place.
    • Start the two nuts on the back side and tighten them up.
    • Finish up by reinstalling the two screws on the top of the trim.

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket

  • Specialty Tools

  • Bent Tipped Awl

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1992-1996 Ford Bronco Headlight Driver Side
  • 1992-1996 Ford F150 Truck Headlight Driver Side
  • 1992-1996 Ford F250 Truck Headlight Driver Side
  • 1997 Ford F250 Truck Headlight Driver Side
  • 1992-1997 Ford F350 Truck Headlight Driver Side
  • 1992-1997 Ford F450 Truck Headlight Driver Side

This part replaces:

  • Partslink FO2502118
  • Hollander 114-548L
  • OE # F2TZ 13008 B
  • TYC 20-1935-00-1
  • DEPO 331-1111L-AS
Part #: 1ALHL00318

How-to Video:

(08:49 min)