A1 CARDONE SELECT CV JOINT AXLE SHAFT (66-2027) RF

This axle shaft is a new, aftermarket part. It is just what you need to get your vehicle in good working order!

Specifications:

  • Fits RH (Passenger Side) FRONT
  • Replaces dealer part numbers: F57Z3B436BA, F57Z 3B436 BA, F5TZ3B414A, F5TZ 3B414 A, 1F0025400
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge

Note: For 2000 models, this fits vehicles WITHOUT Pulse Vacuum hubs. These are the type of hubs where the outer inside diameter of the hub is smooth. A pulse vacuum hub is splined.

Features & Benefits of each NEW CV (Constant Velocity) axle shaft:

  • 100% Neoprene Boots for excellent Ozone resistance. - Eliminates cracking; a leading cause for failure of CV boots
  • 3% moly grease. - Provides excellent high temperature and extreme pressure characteristics which extends the life of the joint
  • Axle nut supplied 100%. - If axle nut from the vehicle is worn or stripped there is no need to buy a separate axle nut because it is provided
  • Splines rolled 100%. - Guarantees proper installation of axle into mating hub and transmission eliminating installation hassle
  • Threads rolled 100%. - Guarantees proper installation of axle nut eliminating installation hassle

Note: This is for one axle shaft assembly.

Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:52)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 32mm axle nut
    • Remove the wheel lock with the wheel lock key
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Rotor (1:52)
    • Remove the two 15mm bolts from the brake caliper bracket
    • Hang the caliper aside with a bungee cord
    • Pull off the brake rotor
  3. step : Removing the CV Axle (2:28)
    • Hold the hub with a pry bar
    • Remove the 32mm axle nut
    • Tap the axle out of the hub with a hammer
    • Remove the 15mm bolt from the upper control arm
    • Tap the wheel spindle loose with a hammer
    • Separate the control arm from the wheel spindle
    • Unclip the ABS sensor wire harness from the frame with trim tools
    • Sepreate the CV axle from the hub
    • Separate the CV Axle from the main axle with a pry bar
  4. step : Installing the CV Axle (4:45)
    • Put the CV axle into place
    • Tap the CV axle into the main axle with a hammer
    • Install the CV axle into the hub
    • Connect the wheel spindle to the upper control arm
    • Tap the upper control arm into the spindle with a hammer
    • Start the 15mm bolt and nut for the control arm
    • Tighten the 15mm bolt to 41 foot-pounds of torque
    • Connect the ABS wire harness to the frame
    • Start the axle nut by hand
  5. step : Installing the Brake Rotor (6:02)
    • Put the rotor into place
    • Put an old axle nut on one wheel stud
    • Thread a lug nut onto that wheel stud by hand to hold the rotor in place
    • Remove the bungee cord from the caliper
    • Put the caliper into place
    • Start the two 15mm bolts for the caliper bracket
    • Tighten the two 15mm bolts to 85 foot-pounds of torque
    • Remove the placeholder lug nut and axle nut
  6. step : Installing the Wheel (6:52)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Tighten the hub nut to 162 foot-pound
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 15mm Socket

  • Specialty Tools

  • Trim Tool Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(07:54 min)

Tools List:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 15mm Socket

  • Specialty Tools

  • Trim Tool Set



This part replaces:

  • A1 Cardone 66-2027

Vehicle Fit

  • 1995-2001 Ford Explorer Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2001-2002 Ford Explorer Sport Trac Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2000 Ford Ranger without Pulse Vacuum Hubs Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2001-2002 Ford Ranger Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2001-2002 Mazda B2300 Truck Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2000 Mazda B2500 Truck without Pulse Vacuum Hubs Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2001 Mazda B2500 Truck Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2001-2002 Mazda B3000 Truck Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2000 Mazda B4000 Truck without Pulse Vacuum Hubs Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 2001-2005 Mazda B4000 Truck Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
  • 1997-2001 Mercury Mountaineer Front CV Axle Shaft Passenger Side A1 Cardone 66-2027
Only 2 left in stock
Part #: CAACV00012

Ships Same Day for orders placed by 4 P.M. ET

A1 CARDONE
Brand #: 66-2027

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More