Replace that caliper hardware today with this high quality replacement set!

Specifications:

  • FRONT or REAR as listed by application
  • Direct replacements
  • Built to strict quality control standards

This caliper hardware kit makes a great replacement and has good cost savings over the factory parts.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:41)
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:11)
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
  3. step : Removing the Rotor and Brake Pads (1:23)
    • Remove T55 Torx bolts from the brake caliper with a T55 Torx bit and ratchet
    • Use either a C-clamp to squeeze the rotor or a screwdriver to pry the brake caliper off
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the two 18mm bolts from the caliper bracket
    • Slide the rotor off
  4. step : Preparing the Rotor and Brake Caliper (3:09)
    • Apply brake cleaner to either side of the rotor
    • Apply brake grease to either end of your brake pads
    • Use a wire brush to clean up the brake slides on the caliper bracket
  5. step : Replacing the Brake Caliper (3:46)
    • Push the rotor back into place
    • Twist on a lug nut
    • Put the caliper back into place and tighten the two 18mm bolts
    • Torque the 18mm bolts to 75 ft/lbs
    • Push the brake pads into place, using a hammer if necessary
    • Using an old brake pad, put it on to the caliper pistons and tighten it in with the C-Clamp
    • Grease up the caliper bolts
    • Put the caliper back into place
    • Slide the slide bolts back in
    • Torque the bolts to 30 ft/lbs
  6. step : Reattaching the Wheel (5:45)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the hubcap and tighten the caps
  7. step : Testing the Brakes (6:20)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Brake Fluid
  • Brake Parts Cleaner

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 22mm Socket

  • Torx Drivers & Sockets

  • T55 Torx Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2002 Cadillac Escalade Rear Caliper Hardware Kit for Models with 4 Wheel Steering
  • 2003-2006 Cadillac Escalade All Wheel Drive Rear Caliper Hardware Kit
  • 2003-2006 Cadillac Escalade ESV Rear Caliper Hardware Kit
  • 2002 Cadillac Escalade EXT Rear Caliper Hardware Kit for Models with 4 Wheel Steering
  • 2003-2006 Cadillac Escalade EXT All Wheel Drive Rear Caliper Hardware Kit
  • 2003-2006 Chevy Avalanche 1500 4 Wheel Drive Rear Caliper Hardware Kit
  • 2005-2006 Chevy Silverado 1500 Front Caliper Hardware Kit for Models with 4 Wheel Steering
  • 2005 Chevy Silverado 1500 7200LB GVW Rear Caliper Hardware Kit without Heavy Duty Brakes
  • 2005-2006 Chevy Silverado 1500 HD Front Caliper Hardware Kit for Models with 4 Wheel Steering
  • 2005 Chevy Silverado 1500 HD 7200LB GVW Rear Caliper Hardware Kit without Heavy Duty Brakes
  • 2000-2002 Chevy Suburban 1500 Rear Caliper Hardware Kit
  • 2003-2006 Chevy Suburban 1500 4 Wheel Drive Rear Caliper Hardware Kit
  • 2000 Chevy Tahoe Rear Caliper Hardware Kit (excluding Z71 Models)
  • 2001-2002 Chevy Tahoe Rear Caliper Hardware Kit
  • 2003-2006 Chevy Tahoe 4 Wheel Drive Rear Caliper Hardware Kit
  • 2005 GMC Sierra 1500 7200LB GVW Rear Caliper Hardware Kit without Heavy Duty Brakes
  • 2005-2006 GMC Sierra 1500 Front Caliper Hardware Kit for Models with 4 Wheel Steering
  • 2005 GMC Sierra 1500 HD 7200LB GVW Rear Caliper Hardware Kit without Heavy Duty Brakes
  • 2005-2006 GMC Sierra 1500 HD Front Caliper Hardware Kit for Models with 4 Wheel Steering
  • 2000 GMC Yukon Rear Caliper Hardware Kit (excluding Denali Models)
  • 2001-2002 GMC Yukon Rear Caliper Hardware Kit
  • 2003-2006 GMC Yukon 4 Wheel Drive Rear Caliper Hardware Kit
  • 2000-2002 GMC Yukon XL 1500 Rear Caliper Hardware Kit
  • 2003-2006 GMC Yukon XL 1500 4 Wheel Drive Rear Caliper Hardware Kit

This part replaces:

  • Dorman HW5659
Only 1 left in stock
Part #: 1ABRX00025

How-to Video:

(06:50 min)