Replaces

2010-15 Chevy Camaro Wheel Bearing & Hub Assembly Rear Timken HA590348 - TKSHR00203

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA590348

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part number: 13500401
  • 3 Bolt Flange
  • Fits 5 Lug Wheel
  • New wheel studs installed
  • Direct replacement
  • Built to strict quality control standards

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Part Details

  • Front or Rear Location: Rear

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:56)
    • Loosen the 22mm lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Separating the Axle from the Hub (1:19)
    • Put the transmission in gear
    • Put the parking brake on
    • Loosen the 32mm axle nut
    • Remove the axle nut
    • Loosen the axle spines with a hammer and punch
  3. step : Removing the Brakes (1:54)
    • Remove the two 16mm bolts from the brake caliper
    • Pull off the brake caliper
    • Hang the caliper aside with bungee cords
    • Remove the T30 Torx screw from the brake rotor
    • Release the parking brake
    • Tap the face of the rotor with a hammer to loosen it
    • Pull off the brake rotor
  4. step : Removing the Hub (3:12)
    • Remove the four 13mm bolts that hold the hub to the wheel spindle
    • Apply a two-jaw puller to the hub
    • Tighten the puller with a socket and ratchet
    • Remove the two-jaw puller
    • Pull the hub off the axle
    • Pull the washer off the axle with a pick
  5. step : Installing the Hub (4:21)
    • Slide the new washer onto the axle
    • Slide the bearing splines onto the axle
    • Start the four 13mm bolts that hold the hub to the wheel spindle
    • Tighten the 13mm bolts to 85 foot-pounds of torque
  6. step : Installing the Brakes (5:04)
    • Put the rotor into place
    • Insert the T30 screw into the rotor
    • Remove the bungee cord from the caliper
    • Put the caliper into pace
    • Start the two 16mm bolts into the caliper
    • Tighten the 16mm bolts to 30 foot-pounds
    • Tighten the 16mm bolts 90 degrees further
  7. step : Installing the Wheel (5:59])
    • Start the axle nut onto the axle
    • Tighten the axle nut to 200 foot-pounds
    • Slide the wheel into place
    • Start the five 22mm lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 140 foot-pounds in a star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Pick
  • Floor Jack
  • Funnel

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • 2 Jaw Gear Puller

  • Torx Drivers & Sockets

  • T30 Torx Bit

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2010-2015 Chevy Camaro Rear Wheel Bearing & Hub Assembly V8 6.2L excluding ZL1 Models Timken HA590348
  • 2010-2015 Chevy Camaro Rear Wheel Bearing & Hub Assembly V6 3.6L with Manual Transmission Timken HA590348

This part replaces:

  • Timken HA590348
  • Hollander 538-00225
  • OE # 13500401
Only 2 left in stock
Part #: TKSHR00203

Timken
Brand #: HA590348

How-to Video:

(07:03 min)