Part Details

  • Color: Chrome & Black

This replacement grille is just what you need to get your vehicle in good looking form again!

Specifications:

  • Brand New Grille
  • Chrome frame with black mesh insert
  • High quality injection molded plastic
  • Replaces dealer part number: 15209577
  • Direct fit replacement
  • Built to strict quality control standards
  • Emblem (nameplate) is not included

This grille makes a great replacement and offers good value over the dealer unit.

NOTE: It is necessary to reuse your original hardware, as new hardware is not included with this item.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Battery (1:07)
    • Undo the tabs that secure the floor mat
    • Snap the plastic cover off of the seat rail
    • Remove the T20 Torx screw from the cover
    • Lift the cover from the floor
    • Disconnect the negative battery terminal with a 10mm socket and ratchet
    • Remove the terminal out of the way
  2. step : Removing the Sight Shield (2:15)
    • Pry up the six plastic retainer pins with a flat blade screwdriver
    • Remove the pins by popping up the sight shield
    • Remove the six T20 Torx screws along the top of the grille and bumper
  3. step : Removing the Wheel Well Liner (3:23)
    • Remove the two 10mm bolts securing the bottom of the bumper
    • Turn the wheel out of the wheel well
    • Remove the seven T20 Torx screws from the outer wheel well liner
    • Remove the eight plastic clips from the inner wheel well liner
    • Pull out on the bottom portion of the wheel liner
    • Remove the wheel liner
  4. step : Removing the Fender Flare (5:31)
    • Pry off the wheel speed sensor retainer from the wheel well
    • Remove the two push pins in the wheel well
    • Remove the six T20 Torx screws on the backside of the fender well
    • Remove the rear wheel well liner
    • Squeeze the backend of the clips with needle nose pliers
    • Remove the outer wheel well liner
  5. step : Removing the Bumper (7:45)
    • Disconnect the fog light wiring harness
    • Have an assistant hold the bumper
    • Remove the 7mm screw on each side of the fender well side of the bumper
    • Have an assistant hold the other side of the bumper
    • Pop the clips out on either end
    • Remove the bumper from the vehicle
  6. step : Removing the Grille (8:39)
    • Remove the two 7mm screws at the top of the grille
    • Collapse the pins on the retaining clips with needle nose pliers
    • Work the grille out of the bumper
    • Remove the grille
  7. step : Installing the Grille (9:21)
    • Insert the grille into place
    • Push up the tabs until they snap in
    • Tighten the 7mm screws
  8. step : Installing the Bumper (9:43)
    • With the help of an assistant, insert the bumper into place
    • Snap the clips in on either end
    • Tighten the two 7mm screws to the bumper
  9. step : Reinstalling the Fender Flare (10:27)
    • Snap the fender flare into the fender holes
    • Insert the rear wheel well liner into place
    • Press on the push clips
    • Tighten the six T20 Torx screws to the liner
    • Reconnect the fog light wiring harness
  10. step : Installing the Wheel Well Liner (11:29)
    • Insert the inner wheel well liner into place
    • Install the eight plastic clips to the inner wheel well liner
    • Install the seven T20 Torx screws to the outer wheel well liner
  11. step : Reinstalling the Sight Shield (12:34)
    • Tighten the 10mm screws to the bottom of the bumper
    • Reinstall the six T20 Torx screws along the top of the bumper
    • Insert the sight shield into place
    • Press on the clips to the sight shield
  12. step : Reconnecting the Battery (13:18)
    • Keep your keys handy
    • Reconnect the negative battery terminal
    • Tighten the 10mm bolt
    • Insert the cover into place
    • Tighten the T20 screw to the cover
    • Reinstall the seat rail cover
    • Insert the floor mat into place and connect the pins

Tools needed for replacement:

    General Tools

  • Assistant

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T20 Torx Driver

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2007-2012GMC Acadia GMC Acadia Chrome & Black Grille

This part replaces:

  • Partslink GM1200585
  • Hollander 104-01975
  • OE # 15209577
Part #: 1ABGR00443


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(14:15 min)