Replaces

2006-08 Dodge Ram 1500 Truck Wheel Bearing & Hub Assembly Timken SP500101 - TKSHF00059

TIMKEN WHEEL BEARING & HUB ASSEMBLY: SP500101

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits LH (Driver Side) FRONT
  • Direct replacement for 1500 2wd or 4wd models
  • Fits 5 Lug Wheel
  • 3 bolt flange
  • Studs already installed
  • Correct for models that have a Speed Sensor on the LH (Driver Side)
  • Correct for Models that do Not have ABS on the front wheels but do have the LH (Driver Side) Sensor used for Speed input
  • Does not fit MEGA CAB Models (these have 8 Lug Wheels)

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel and tire (1:13)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (1:40)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
  3. step : Remove brake disk (3:00)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (3:16)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a pry bar to remove the axle.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (9:26)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 100 ft lbs.
    • Reinstall the ABS harness.
    • Replace the axle.
    • Tighten but don't torque the lug nut.
  6. step : Put brakes and wheel back on (11:40)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 120 ft lbs
    • Hub nut is 185 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket

  • Sockets - SAE

  • 13/16 Inch Socket
  • 7/8 Inch Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2006-2008 Dodge Ram 1500 Truck Quad Cab Front Wheel Bearing & Hub Assembly for Models with Speed Sensor & Rear Wheel ABS Brakes Driver Side Timken SP500101
  • 2006-2008 Dodge Ram 1500 Truck Regular Cab Front Wheel Bearing & Hub Assembly for Models with Speed Sensor & Rear Wheel ABS Brakes Driver Side Timken SP500101

This part replaces:

  • Timken SP500101
Only 2 left in stock
Part #: TKSHF00059

Timken
Brand #: SP500101

How-to Video:

(13:39 min)