Replaces

2005 Wheel Bearing & Hub Assembly Rear Pair ACDelco FW293 - ACSHS00004

AC DELCO Wheel Bearing & Hub Assembly Pair: FW293

These AC DELCO wheel bearing assemblies are original replacement parts. The same pieces that you would receive if purchased from your local GM dealer.

Specifications:

  • Brand New AC Delco Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) REAR
  • 3 Bolt Triangular Flanges
  • Fit 5 Lug Wheels
  • Replaces dealer part number: 88964168
  • Wheel studs included and installed
  • Direct replacements
  • Built to strict quality control standards
  • Fit AWD (All Wheel Drive) Models only
    • Do NOT fit FWD (Front Wheel Drive) Models

Part Details

  • Front or Rear Location: Rear
  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the wheel and tire (1:30)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (2:00)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 15mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
  3. step : Remove brake disk (2:44)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (2:56)
    • Remove the 3 bolts securing the hub using your 13mm socket and 3/8 extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a rubber mallet to break it free, and work around the flange with the hammer to pull it off.
    • Leave the top 13mm loosely still in to prevent the hub from flying out if you hit it too hard.
    • Remove the hub, using driving tools to help work it out of the steering knuckle.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (8:30)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Watch part 2 to install your new 1A Auto hub!

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 19mm Socket
  • 32mm Socket
  • 35mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2005Buick Terraza Buick Terraza Rear Wheel Bearing & Hub Assembly Pair All Wheel Drive ACDelco FW293
2005Chevy Uplander Chevy Uplander Rear Wheel Bearing & Hub Assembly Pair All Wheel Drive ACDelco FW293
2005Pontiac Montana SV6 Pontiac Montana SV6 All Wheel Drive Rear Wheel Bearing & Hub Assembly Pair ACDelco FW293
2005Saturn Relay Saturn Relay Rear Wheel Bearing & Hub Assembly Pair All Wheel Drive ACDelco FW293

This part replaces:

  • ACDelco FW293
Part #: ACSHS00004

Out of Stock

AC DELCO
Brand #: FW293

How-to Video:

(09:37 min)