Replaces

2003-2013 Ford Expedition Front Auto-Locking Hub Actuator Pair

  • New

These auto-locking hub actuators are just what you need to get your 4WD system working again!

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part number: 7L1Z-3C247-A, 7L1Z3C247A
  • Direct replacements
  • Built to strict quality control standards

These actuators makes a great replacement and has good cost savings over the dealer part!

2 Year Warranty

This item is backed by a 2 Year  Manufacturers Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Raise and Secure the Vehicle
    • Raise the vehicle with a jack
    • Secure the vehicle on jack stands
  2. Removing the CV Axle Shaft
    • Pry off the wheel center cap with a flat blade screwdriver
    • Remove the cap over the hub nut
    • Remove the 13mm hub nut
    • While holding the tire in place, remove the six twelve-point 12mm bolts from the CV joint
    • Remove the 30mm bolt from the strut assembly using a breaker bar or ratchet and pipe
    • Tap the nut with a hammer to loosen it, if necessary
    • Pry the lower end of the strut assembly from the lower control arm with a pry bar
    • Pull out the CV shaft
  3. Removing the Four Wheel Drive Actuator
    • Remove the three 8mm bolts from the four wheel drive actuator
    • Pry off the actuator with a flat blade screwdriver
    • Disconnect the vacuum hoses from the actuator
  4. Installing the New Actuator
    • Connect the vacuum hoses to the new actuator
    • Put the actuator into place
    • Start the three 8mm bolts by hand
    • Tighten the three 8mm bolts
  5. Reattaching the CV Axle
    • Slide the CV Axle back into place
    • Reconnect the strut at the lower control arm
    • Push the bolt through where the strut connects to the lower control arm
    • Attach the nut
    • Tighten the bolt to between 95-100 foot-pounds of torque
    • Start the 12-point 12mm bolts into the CV axle by hand
    • Tighten the bolts preliminarily
    • Tighten the bolts to 25 foot-pounds in a crossing or star pattern
    • Reinstall the 13mm nut on the end of the axle
    • Reinstall the cap over the nut
    • Reinstall the center cap
    • Lower the vehicle

How-to Video:

(08:51 min)

Tools List:

    Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 12mm Socket
  • 13mm Socket
  • 24mm Socket
  • 30mm Socket
  • 8mm Socket

  • Specialty Tools

  • A Piece of Pipe (for leverage)
  • Floor Jack
  • Hammer
  • Jack Stands




Vehicle Fit

  • 2003-2013 Ford Expedition Front Auto-Locking Hub Actuator Pair
  • 2004 Ford F150 Truck New Body Style Front Auto-Locking Hub Actuator Pair
  • 2005-2013 Ford F150 Truck Front Auto-Locking Hub Actuator Pair
  • 2006-2008 Lincoln Mark LT Front Auto-Locking Hub Actuator Pair
  • 2003-2013 Lincoln Navigator Front Auto-Locking Hub Actuator Pair
$180.45
Save 26%
List: $244.06 Save: $63.61
Part #: 1ASHS00588

Out of Stock

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est