Replaces

1993-1997 Dodge Intrepid Headlight Mounting Bracket Driver Side

Part Details

  • Location: Driver Side

This part replaces:

  • OE # 4746455
  • PARTSLINK CH2508104

  • New

Specifications

  • Left Hand (driver's side)
  • Includes leveling bubble
Fit guaranteed
  • This headlamp will install just as your original does. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.
Quality
  • 1A Auto has the most comprehensive warranty.
  • If this headlight should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.
Value
  • Replacing a discolored, scratched, dull or damaged headlight with a headlight from 1A Auto can increase your resale value by up to 10%.
Safety
  • A new headlight can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new headlight from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather.

Warranty

Please inspect this part carefully prior to installation and contact us with any questions BEFORE attempting to install it. Due to the nature of this part, our 60-day warranty covers exchanges only. Parts that have been installed, neglected, or modified in any way are not eligible for this exchange.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

  1. Removing the Bumper Cover (0:58 in the video)
    • Remove the six Phillips screws in the front of the wheel well.
    • Pull the inner fender panel down.
    • Remove the 3/8â€� bolt from behind the inner fender panel.
    • Do the same process in the opposite wheel well.
    • Remove the five 3/8 bulbs from the bottom of the bumper cover.
    • Pull the bumper cover out on either side and off.
    • Disconnect the fog lights and put the bumper cover aside.
  2. Removing the Headlight Bracket (3:18 in the video)
    • Push the tab on the back of the parking light and pull the light free.
    • If keeping the headlight remove it by removing the two screws on the sides and loosening the center screw.
    • Remove the four 10mm bolts securing the bracket to the car.
    • Pull the bracket free.
  3. Replacing the Headlight Bracket (4:30 in the video)
    • Remove the clip from the new one and replace it with the old clip.
    • Put the bracket into place making sure the wire harness goes up through the hole on the back.
    • Replace those four 10mm bolts.
    • Reconnect the headlight and replace the light.
    • Replace the three screws.
  4. Adjusting the Headlight (5:50 in the video)
    • Using the two screws at the top of the headlight aim the lights.
    • The screw on the inside controls left and right. The one on the outside angles it up and down.
    • Aim the light at a wall 20 feet away.
    • The concentration of the low beam on the wall should be 1â€� below the bulb. And straight ahead.
    • The high beam concentration should line up with the low beam bulb.
  5. Replacing the Bumper Cover (6:12 in the video)
    • Reinstall the parking light.
    • Reconnect the fog lights.
    • Place the bumper into place and connect the clips on either side.
    • Replace the bolt inside the inner fender.
    • Replace the six bolts that secure the inner fender.
    • Repeat this on both sides. Use an awl to help line up the fender by pushing it through the screw holes.
    • Replace the five 3/8â€� bolts under the bumper cover.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Sockets - SAE

  • 3/8 Inch Socket

  • Torx Drivers & Sockets

  • T15 Torx Driver

How-to Video:

(10:03 min)

Tools List:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Sockets - SAE

  • 3/8 Inch Socket

  • Torx Drivers & Sockets

  • T15 Torx Driver



This part replaces:

  • OE # 4746455
  • PARTSLINK CH2508104

Vehicle Fit

  • 1993-1997 Dodge Intrepid Headlight Mounting Bracket Driver Side
$48.45
Part #: 1ALHL00467

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est