WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
How to Replace Washer Pump 2002-06 Chevy Avalanche
Created on:
Tools used
Socket Extensions
Flat Blade Screwdriver
15mm Socket
Rust Penetrant
7mm Socket
Drain Pan
10mm Socket
Ratchet
1. Removing the Fog Light
Remove the 10mm bolt from the bracket
Remove the two 15mm bolts from the bracket
Remove the 7mm bolts from the four mounting locations on the fog light
Press the tab on the socket or disconnect the wiring harness
Turn the socket counterclockwise
Remove the fog light
2. Removing the Washer Pump
Have a drain pan ready
Pull the hose out of the pump
Let the fluid drain
Disconnect the fluid lead
3. Installing the Washer Pump
Connect the lead to the pump
Connect the line to the washer
Press the pump into the washer bottle
4. Installing the Fog Light
Insert the fog light into place
Tighten the four 7mm bolts to the fog light mount
Pull the bulb straight out
Press the new bulb onto the socket
Turn the socket clockwise
Connect the wiring harness
Insert the bracket into place
Tighten the two 15mm bolts to the bracket
Tighten the 10mm bolt to the bracket
Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. We've created thousands of videos to help you install our parts with confidence. That saves you time and money, so visit us at 1AAuto.com, your trusted source for quality auto parts.
In order to get your old light down if it's in one place or to get your new light up, you need to remove this bracket, which is one 10 millimeter bolt here and two 15 millimeter bolts here. I'm just going to use some rust penetrant and spray the back side before I remove them. I loosened the small one, and I removed the two big ones. I'll just let it kind of hang out of the way. And by looking at our new fog light, you can see to remove it, there's four mounting holes. There's four mounting locations. There's seven millimeter bolts that hold it to the top. At the base four corners. So, those bolts underneath. And underneath, you can see two are very easy to see. There and there. And two are more difficult to point out, but there on the sides. You'll want a seven millimeter socket with an extension and a ratchet and remove those bolts. Remove this bracket detached, gently pull it down. Pull your light out.
I have a bucket underneath to catch any fluid that comes out. We're going to pry up. You actually want to pull out the top of the pump first and then pry up. You're going to get all kinds of fluid coming out. Try and control it until it drains out, and just let that drain for right now. With most of the fluid now drained out, you want to disconnect your fluid lead, which you just twist, get loosened up from the washer pump, and pull it off. And then disconnect your electrical lead. Disconnect this little tab, pull up, and take the pump is off.
Replacement pump back in, hook up the connector first. Bring it up close. Hook up your washer line feed and then push it up into place. There's another harness that you kind of have to move out of the way. Push it up into place. Put the pickup down in, push it in, and then push it back against the bottle to lock it in place.
Gently kind of pull down on this. Feed your new light up into place. It'll start in the seven millimeter bolts to hold it. Put the driving light bulb in. In, lock it in and then reconnect our fog light. Now we'll put this bracket back in place. Tighten these up first. And then adjust it back to where it was and tighten up the 10 millimeter bolt. Now refill your washer fluid right here next to your battery in this vehicle. And recap it.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
WWA06633
In Stock
Product Reviews
Loading reviews
4.50/ 5.04
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
1
0
0
Michael
December 14, 2022
Excellent
Windshield washer pump
Dean
December 27, 2022
The videos are a real help for me , not use to working on the newer cars and trucks. The part was top quality and delivered fairly soon. I will keep using 1A auto.
Cheaply made product.
John
March 9, 2023
The hose connections should have been made with a more ridged plastic instead of a soft plastic. I'll buy else where for next one#
Jerone
March 16, 2023
????
Customer Q&A
In the video for the 08 CTS, the tech said it was a windshield washer pump at the beginning. Then for the reinstall, he called it a headlight washer pump. Which is it??August 5, 2022
John D
10
This part is for a windshield washer pump.
August 5, 2022
Andra M
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.