Replaces

Toyota 4Runner FJ Cruiser Tacoma Front Passenger Side Strut & Spring Assembly TRQ - 1ASTS01599

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:22)
    • Raise the vehicle with minimal weight on the wheel
    • Loosen the six 21 mm lug nuts
    • Raise and support the vehicle
    • Remove the six lug nuts
    • Remove the wheel
  2. step : Removing the Front Strut (0:46)
    • Remove the 10 mm ABS wire bracket bolt to remove the bracket
    • Remove the upper ball joint castle nut pin
    • Remove the 19 mm upper ball joint castle nut
    • Hammer the knuckle around the ball joint to loosen it from the knuckle
    • Tie off the knuckle so that the axle does not fall out
    • Remove the 12 mm ABS wire bracket bolt from the knuckle to remove the bracket
    • Remove the 19 mm nut from the 19 mm lower strut bolt
    • Remove the lower strut bolt
    • Remove the three 14 mm top strut mount nuts
    • Remove the 17 mm sway bar link nut to remove the sway bar link from the knuckle
    • Remove the sway bar link from the knuckle on the opposite side of the vehicle to freely move the sway bar for clearance
    • Remove the strut
  3. step : Installing the Strut (10:07)
    • Insert the strut top mounting studs into the body, and slide the bottom mount into the bracket
    • Install the three 14 mm strut top mounting nuts
    • Install the 19 mm lower strut bolt
    • Install the washer and 19 mm nut onto the lower strut bolt
    • Torque the 14 mm top mount nuts to 47 ft-lb
    • Torque the 19 mm lower strut nut to 100 ft-lb
    • Install the upper ball joint into the knuckle
    • Install the 19 mm upper ball joint castle nut
    • Torque the upper ball joint castle nut to 81 ft-lb, then tighten further to align the pin hole, if necessary
    • Install the upper ball joint pin
    • Reinstall the ABS wire bracket to the upper control arm with the 10 mm nut
    • Reinstall the sway bar links into the knuckles
    • Reinstall the ABS wire bracket onto the knuckle with the 12 mm bolt
  4. step : Installing the Wheel (17:16)
    • Install the wheel onto the wheel studs
    • Install the six lug nuts and tighten them by hand in a crossing pattern
    • Lower the vehicle with minimal weight on the wheel
    • Torque the 21 mm lug nuts to 85 ft-lb in a crossing pattern
    • Lower the vehicle completely

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Locking Pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pocket Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 14mm Socket
  • 17mm Socket
  • 19mm Socket
  • 21mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 19mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2003-2016Toyota 4Runner Toyota 4Runner (without X-REAS Suspension System) Front Passenger Side Strut & Spring Assembly
2007-2013Toyota FJ Cruiser Toyota FJ Cruiser Front Passenger Side Strut & Spring Assembly
2005-2015Toyota Tacoma Toyota Tacoma 4 Wheel Drive Front Passenger Side Strut & Spring Assembly
2005-2015Toyota Tacoma Toyota Tacoma Pre Runner Rear Wheel Drive Front Passenger Side Strut & Spring Assembly
Part 1ASTS01599
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: SCA70141