1ASTS02229-Nissan Rogue Front Driver Side Strut & Spring Assembly

Replaces

Nissan Rogue Front Driver Side Strut & Spring Assembly TRQ SCA57995

1ASTS02229

Part Details

This part replaces:

  • Hollander 527-50528L
  • Monroe 172609
  • Monroe 272609
  • KYB SR4437
FREE SAME DAY SHIPPING
Save 27%
List: $167.95 Save: $45.00
Part 1ASTS02229
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: SCA57995

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Strut Assembly (1:36)
    • Pry off the flexible brake hose from the clip
    • Remove the rubber retainer for the ABS sensor
    • Place locking jaw pliers on the backside of the sway bar link joint
    • Remove the nut with an 18mm socket and ratchet
    • Remove the sway bar link from the strut
    • Remove the 21mm bottom strut bolts
    • Move the spindle out of the strut
    • Remove the rubber cover on the cowl panel
    • Remove the inside 13mm bolts
    • Loosen the last 13mm down to the end of the threads
    • Support the strut without pushing up
    • Lower the strut down and out
    • Leave the bolt in the socket extension
  3. step : Installing the Strut Assembly (5:15)
    • Set the thread into the nut on the new strut on the bolt
    • Set the strut into place
    • Tighten the 13mm bolt
    • Tighten the inside 13mm bolts
    • Reinstall the steering knuckle into the bottom of the strut
    • Tighten the 21mm bolt to the bottom of the strut
    • Clip locking pliers to the back of the sway bar link
    • Tighten the 18mm nut to the sway bar link
    • Reconnect the ABS harness to the hangers
    • Slide the brake hose into place
    • Reinstall the spring clip and tap it in
  4. step : Reattaching the Wheel (8:02)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 18mm Socket
  • 13mm Socket

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
2008-2011Nissan Rogue Nissan Rogue Front Driver Side Strut & Spring Assembly
2012Nissan Rogue Nissan Rogue (Built Before 1/12 Production Date) Front Driver Side Strut & Spring Assembly

Part Interchange

Brand Label Part Number
KYB SR4437
KYB Shocks & Struts SR4437
Monroe 272609
Monroe 172609
Monroe Shocks & Struts 172609
Monroe Shocks & Struts 272609
Unity Automotive 11733

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: SCA57995
Product Reviews
There are no reviews for this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Nissan Rogue Front Driver Side Strut & Spring Assembly TRQ SCA57995-1ASTS02229 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.