Kit Includes: (2) Front Outer Tie Rods (2) Front Lower Control Arms with Ball Joints (2) Front Sway Bar Links (2) Rear Sway Bar Links (2) Front Inner Tie Rods (2) Front Steering Rack & Pinion Bellows
Specification
Trim
S
Location
Front & Rear
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Application Specific Design: No modifications necessary
Anti-Corrosion Coated: Enhanced surface life
Pre-greased: No additional maintenance required
Kitted for Restored Performance: Improved road-feel and handling
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Rear Sway Bar Link 2008-13 Mazda 3
How to Replace Rear Sway Bar Links 2007-12 Volvo S40
How to Replace Outer Tie Rods 2004-14 Mazda 3
How to Replace Rear Sway Bar Links 2007-12 Volvo S40
How to Replace Bellows Boot 2007-12 Nissan Sentra
How to Replace Rear Sway Bar Links 2004-13 Mazda 3
Created on:
Tools used
6mm Allen Wrench
Torque Wrench
Locking Pliers
14mm Socket
Pry Bar
Ratchet
Tools used
8mm Allen Wrench
Pry Bar
13mm Wrench
Tools used
Socket Extensions
Torque Wrench
14mm Socket
Hammer
Rust Penetrant
16mm Socket
Jack Stands
Liquid Thread Locker
21mm Socket
24mm Wrench
Ratchet
Floor Jack
1/2 Inch Breaker Bar
Wire Cutters
1. Removing the Wheel
Loosen the 21mm lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Outer Tie Rod
Loosen the 24mm jamb nut with a 24mm wrench
Remove the cotter pin
Remove the 14mm nut from the tie rod
Tap the end of the knuckle with a hammer to pop the stud out
Turn the tie rod counterclockwise to remove
3. Installing the Outer Tie Rod
Apply anti-seize to the threads
Thread the outer tie rod on to the jamb nut
Install the castle nut by hand
Tighten the 16mm castle nut with a socket and ratchet
Insert the cotter pin and fold the ends to secure it
Tighten the jamb nut with a 24mm wrench
4. Reattaching the Wheel
Slide the wheel into place
Start the 21mm lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 87 foot-pounds in a crossing or star pattern
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Hey everyone, Sue here at 1A Auto. And today we're installing outer tie rod ends on our '07 Mazda 3 sedan. These came from 1A Auto, so if you need this part or any other part for your car, click on the link below and head on over to 1A Auto.
Keep in mind before this repair, set up an appointment with your local alignment shop and you're going to need an alignment afterwards.
We're going to loosen the lug nuts with the weight of the car on the tire and it's a 21 millimeter. Now you're going to raise the vehicle with a jack and jack stands or a two post lift if you have that. Now I can take the lug nuts off. It's up in the air.
This is the inner tie rod end. It has a bellow boot that covers the end that screws into the power steering rack, and this is your outer tie rod end. This is a jam nut. This is where adjustments are made for a tow on a car. I'm going to start by spraying the jam nut and the upper part of the outer tire rod end. Let that soak. I'm going to break the jam nut free first. It's a 24 millimeter on this Mazda 3. Now that's broken free and spinning I have to undo the top nut to the outer tie rod end, take this cotter pin out. We discard it because we're going to use a new one. The nut is a 14 millimeter socket. It's kind of rusted so just wiggle it on down there. I'm going to break it free. Now I'm going to take a hammer and hit the end of the knuckle where the tie rod end goes in to pop the stud out.
Here we have outer tie rod ends on our '07 Mazda 3 sedan. This one is from 1aauto.com, and this is the one we took out. The one from 1aauto.com is stamped clearly, R for right side, the passenger side, comes with its own new castle nut and a cotter pin. If you need this part or any other part for your car, click on the link below and head on over to 1aauto.com.
Now I'm just going to put some anti-seize on the threads. Now install the outer tie rod end. Thread it on up to the jam nut. I'm going to bring it up, put it in the knuckle, install my castle nut. The new one is a 16 millimeter socket. There is no torque for this. I just really want it down tight. There we go.
Now I can install my cotter pin. Just fold that over. That just stops the nut from possibly on back threading out. I like to squeeze all sharp edges down, only fair to somebody. Now we're going to take our wrench and tighten up the jam nut. You want that snug right down because you do have to drive it to the alignment shop. That's a 24 millimeter wrench, same as the old one. There we go. Once I lower this to the ground always tighten wheels in a star pattern. And our wheel torque on our '07 Mazda 3 is 87 foot-pounds. Always go around twice.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
8mm Allen Wrench
Pry Bar
13mm Wrench
Tools used
21mm Socket
Torque Wrench
Socket Extensions
Locking Pliers
14mm Socket
Hammer
Pry Bar
Copper Anti-Seize
19mm Socket
Wire Ties
Needle nose pliers
Pliers
Tools used
PSA59044
In Stock
Product Reviews
Loading reviews
4.67/ 5.09
9 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
6
3
0
0
0
Good parts but some were of lower quality
C
April 1, 2018
Firstly I want to point out that the price was lower through 1A Auto than anywhere else and I looked for weeks also shipping was free and package arrived in a couple days. That alone made me a happy buyer. Now on to the technical part of the review. I bought 2 lower control arms (ball joints included), 2 inner tie rods, 2 putter tie rods, 2 bellows, 2 sway bar links, and 2 rear suspension links. All parts so far were of good quality except a rear suspension link, and one of the outter tie rods were kind of loose (fairly easy to move around) this doesnt mean theyre bad just as a mechanic Ive always been taught that new ball joints, tie rods etc. are supposed to be very hard to move by hand. The packaging looked like a cheetah was also shipped in the box because the boxes of bellows were shredded and the zip ties provided by 1A auto Im sure worked their way out of the box during shipping. On another note I did not realize it at the time but the bolts and nuts are NOT included luckily I w
Mazda 3
P
November 12, 2019
Everything fit perfectly and car handles much better. Knocks and rattles gone. Package shipped quickly but box was pretty damaged. Parts were in good condition. I would recommend buying from 1A Auto in the future.
B
January 28, 2020
My order showed up on time. All parts were just as show and all went on without any hassles. Everything is work just a perfect, have driven just over 1,000 miles on the new parts. So far so good. Thanks for the affordable parts.
MY supension rebuild
N
March 11, 2020
I recently ordered and installed a 1a Auto 12 piece kit for My brothers 2006 Madza 3. The Feel of the car when driving was night and day. Showing me how dangerous the previous conditions were. The 1a auto Kit definitely met my expectations and proved to be a suitable product.
Received parts
ALEXANDER
April 22, 2020
I received all parts requested without any damages or missing parts. Thank you for your service.
Front suspension
Mario
April 6, 2021
All the parts are good quality I got everything as described and perfect match. I got everything in a descent time frame I will and have been using A1auto. Very happy with your product..
Not sure yet
hunter
August 13, 2021
There was missing nuts for a few of the items and one of the sway bar links had bad bushings. Other then that pretty good
Good
moises
August 24, 2022
Everything works good suggest to upgrade sway bar link to a better brand
Suspensin mazda 3
Jesus
September 7, 2023
Every single part was perfect
Everything fit in it!!
And affordable price for the set ????
Customer Q&A
Is this for the front lower?January 28, 2018
Xx X
10
Yes
January 28, 2018
A L
Do you guys do payment plan?February 25, 2020
Jaypee B
10
We do not have any payment plans at this time. Please do not hesitate to contact us with any further questions.
February 25, 2020
Emma F
Will these parts fit 2007 Mazda 3 with the 2.3l ?May 21, 2020
Ezekiel I
10
Yes, according to the information you provided, this part will fit your vehicle as long as it's not the MAZDASPEED model. Please let us know if you have any other questions!
May 21, 2020
Adam G
What is the difference in this kit and the 10 piece other than it being $20 less for 2 more parts?November 3, 2020
Chase L
10
The parts within the kit may be different which could lead to the price discrepancy.
November 3, 2020
Emma F
Do you have a steering and suspension kit for the speed3?May 31, 2021
Chris S
10
Currently, we do not carry this part for your vehicle. We're always updating our inventory so please check back soon!
June 1, 2021
Ricale A
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Mazda is a registered trademark of Mazda Motor Corporation. 1A Auto is not affiliated with or sponsored by Mazda or Mazda Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.