TKSHF00178-Honda Acura Front Wheel Bearing

Replaces

Honda Acura Front Wheel Bearing Timken 510030

TKSHF00178

This part replaces:

  • OE # 44300S5A008
FREE SAME DAY SHIPPING
Save 34%
List: $112.95 Save: $38.00
Part TKSHF00178

Out of Stock

Free GROUND SHIPPING

Close



Timken
Brand #: 510030
Description
Vehicle Fit
Warranty & Shipping
How-To & Tools

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (0:55)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:25)
    • Remove the dust cap with a chisel and hammer
    • Insert a tapered punch into the punched slit between the retainer and nut
    • Tap the punch to separate the nut
    • Remove the 32mm nut axle nut with a pry bar and breaker bar
  3. step : Removing the Caliper (1:52)
    • Remove the 17mm bolts from the caliper bracket
    • Remove the caliper and caliper brackets assembly from the rotor
    • Hand the caliper with a wire tie or bungee
  4. step : Separating the Ball Joint (2:28)
    • Bend the cotter pin tab out with needle nose pliers
    • Pry the cotter pin out
    • Remove the 17mm castle nut on the bottom of the ball joint
    • Tap up with a hammer to release the ball joint
    • Use a pickle fork to separate the ball joint if needed
  5. step : Removing the Spindle (3:45)
    • Remove the 22mm bolts from the bottom of the strut
    • Unbolt the wheel speed sensor with a 10mm socket and ratchet
    • Remove the sensor with a pair of pliers
    • Tap the center of the CV axle
    • Pull the axle out of the spindle
  6. step : Removing the Backing Plate and Hub (5:04)
    • Insert the hub and rotor into the hydraulic press
    • Press the hub out of the bearing
    • Remove the three Phillips screws from the backing plate
    • Remove the backing plate
  7. step : Removing the Bearing (5:37)
    • Squeeze the snap ring with snap ring pliers
    • Pry the snap ring out with a flat blade screwdriver
    • Press the bearing out with a hydraulic press
  8. step : Installing the Bearing (6:15)
    • Press the bearing into the knuckle with a hydraulic press
    • Attach the snap ring to a pair of snap ring pliers
    • Press the snap ring into the bearing
  9. step : Installing the Backing Plate and Hub (6:28)
    • Insert the backing plate to the knuckle
    • Tighten the three Phillips screws to the backing plate
    • Place the old bearing on the back of the inner bearing for support
    • Place the spindle into the hydraulic press
    • Insert the hub into the spindle with the hydraulic press until it bottoms out
  10. step : Installing the Spindle (7:04)
    • Insert the lower ball joint into the control arm
    • Line up and press the CV Axle into the hub
    • Insert the 22mm bolts (head facing front of car) into the bottom of the strut
    • Torque the strut bolts to 116 foot-pounds with a 19mm wrench on the bolt side
  11. step : Installing the Hub Nut (8:34)
    • Insert the hub nut into place
    • Torque the 32mm hub nut to 134 foot-pounds with a pry bar to keep the hub still
    • Dent the outer ring on the axle nut into the keeper groove with a hammer and pick
    • Tighten the 10mm bolt to the wheel speed sensor
  12. step : Installing the Ball Joint (9:38)
    • Align the castle nut with the windows on the control arm
    • Torque the castle nut to 43-50 foot-pounds
    • Insert the cotter pin into nut
    • Bend the cotter pin underneath
  13. step : Reinstalling the Brake Caliper (10:33)
    • Insert the brake rotor into place
    • Tighten the Number 2 Phillips screw to the brake rotor
    • Spread the pads and insert the caliper into place
    • Tighten the 17mm caliper bolts
    • Torque the caliper bolts to 80 foot-pounds
  14. step : Reattaching the Wheel (11:45)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 17mm Socket
  • 22mm Socket
  • 10mm Socket


Fits the following Makes:

Year Make Model Description
1994-2001Acura Integra Acura Integra Front Wheel Bearing
1992-2000Honda Civic Honda Civic SI Front Wheel Bearing
1992-2000Honda Civic Honda Civic EX Front Wheel Bearing
2001-2003Honda Civic Honda Civic Front Wheel Bearing
2004-2005Honda Civic Honda Civic Hybrid Front Wheel Bearing
2004-2005Honda Civic Honda Civic HX Front Wheel Bearing
2004-2005Honda Civic Honda Civic GX Front Wheel Bearing
2004-2005Honda Civic Honda Civic EX Front Wheel Bearing
2004-2005Honda Civic Honda Civic DX Front Wheel Bearing
2004-2005Honda Civic Honda Civic Value Package Front Wheel Bearing
2004-2005Honda Civic Honda Civic LX Front Wheel Bearing
2005Honda Civic Honda Civic EX Special Edition Front Wheel Bearing
2005Honda Civic Honda Civic LX Special Edition Front Wheel Bearing
1994-1997Honda Civic Del Sol Honda Civic Del Sol with ABS Brakes Front Wheel Bearing

Part Interchange

Brand Label Part Number
DIY Solutions HUB01229

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
Timken
Brand #: 510030
Product Reviews
There are no reviews for this item.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Honda Acura Front Wheel Bearing Timken 510030-TKSHF00178 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.