WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Tailgate Handle Bezel 1999-2006 GMC Sierra
How to Replace Tailgate Handle Bezel 1999-2006 Chevy Silverado
Created on:
Tools used
1/2 Inch Wrench
Razor Blade / Gasket Scraper
1. Remove the tail gate handle
Push down and out to unclip the tail gate handle bezel.
Remove the three bolts on the back of the tail gate.
Use a razor blade to cut through the rhino-liner to access the bolts.
Remove the door handle by unclipping the handle latch rods.
2. Install the new tail gate handle
Add some white grease to the hinges in the handle.
Clip the latch rods in.
Bolt the tail gate handle back in using your wrench.
Clip the tail gate handle bezel back in.
Brought to you by www.1AAuto.com. Your source for quality replacement parts and the best service on the internet.
Hi I'm Mike Green. I'm one of the owners of 1A auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my twenty plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1aauto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.
In this video we'll be doing a tailgate handle on a 2004 GMC Sierra. Same as any 99-06 Sierra Silverado. Only tools needed are a half inch wrench and an Exact-o knife if you have a Rhino liner in your truck. Also if you're going to order the tailgate handle we do recommend ordering the bezel as it's kind of difficult to get off without breaking it and actually we found on our truck it had already been broken. So it'll just save you a little time.
Okay, so to remove your tailgate handle the first thing you want to do it is remove this bezel. Basically there are two pins that go down and then it clips in. So you want to push down on top and then pull out, this is interesting. This truck has already been damaged and somebody used two sided tape to put it in there. See the close up, the tabs are broken off. It commonly happens. Two sided tape is okay for awhile, the problem is what happens is these trucks, the dirt just kind of swirls up and around here and sooner or later the two sided tape is going to let go and this thing's going to look like that.
Here on the tailgate you've got three bolts, you can see ones already loose because I was experimenting a bit. This truck's got a Rhino liner in it and a lot of trucks do now. If you don't obviously you can just take these bolts off but if you do have a Rhino Liner you want to use a knife and you just basically want to cut very carefully, so you don't cut your fingers off, cut each hex. I'm trying to do this quick. If you don't cut this off you won't be able to get your wrench on there. You could probably force your wrench on there but this is the best way not ruin your bolts. Just kind of back it in there and peel it off. You don't have to get it all off, it doesn't have to be perfect but you definitely need to get enough off so that you can get your wrench on there. Okay it's a half a inch, you push down and the bolt comes up and out. You want to remove these three bolts.
As I was taking these out I wasn't filming because you don't really need to see me tearing out but something funny, this has washers and the Rhino Liner has actually trapped the washers in there but that's okay. You can just remove it to that point and you'll still be able to remove your handle. You just back it out and you can hear my handle just dropped down there's. We're going to put our bolts on our 1A Auto magnetic tray.
Okay here's your handle and there's two rods right here held in by clips and basically you just need to move these clips down. Okay and the rod pulls out and then there's your tailgate handle. New handle, see it's all basically the same as the old handle. Okay what you want to do always, is lubricate. Any point where it might pivot, spray them with a bunch of stuff. Put it in here and it'll attach. This goes that way. Push them in. Push these rods into the clips. They don't want to go easily, there's it goes, it's kind of working in a little bit. You basically do it one side at time, just kind of grab the rod, push on the tailgate. Grab this rod, push on the tailgate and it'll open up.
Okay then down here and we'll take the handle and we can line it up by and I'll need my wrench here. These washers are kind of stuck in here. Get that bit with no problem. The last one here. As far as tightening, it doesn't have to be incredibly tight. Holding it with my fist, and that's good. So we have our new bezel here and here's the old one, you can see the little teeth that are broken off. Remove some of the two sided tape because it needs to bite under the metal and that will just get in the way. Basically this just goes in. Push down on it and there you go all set.
This video was brought to you www.1AAuto.com. We hope we helped you out. We are your source for quality replacement parts and the best service on the internet. Feel free to call us toll free 888-844-3393 we're here for you on the internet and in person. Thank you very much.
Tools used
13mm Socket
Ratchet
Trim Tool Set
First thing you're going to want to do is make sure that your tailgate is down. Once you have it open and down, you're going to see these three bolts right there, remove those using a 13-millimeter socket. Nice and tight. Let's get these out of here. Wiggle this handle around so it's nice and free. With this black bezel, the next thing you're going to want to have is one of these nice plastic trim tools. The reason why we're going to use plastic is because we're going to come in between the bed and the plastic shroud right here. Just go ahead and come right here, push it, do the same thing right there. Once you have the top broken free, just go ahead and lift this straight up and draw it away.
We can continue on to installing this. If you were to pay attention on the backside, you're going to see that you have a couple little pitons, and then right here you have some hooky-dos. When you go to install this, you're going to put the bottom in first so that the pitons go down into here, they'll latch in and then just roll it in and it'll latch. So with this, in. So now from inside the bed, you can see the backside of the tailgate, we're just gonna kind of wiggle the handle around until we can see our bolt holes. Grab your bolts, go ahead and start all three of them in before you tighten any of them down. Let's go ahead and snug them up.
DHA64736
In Stock
Product Reviews
Loading reviews
4.83/ 5.06
6 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
5
1
0
0
0
Simple and easy
Tyler
February 24, 2017
Easy to order shipping on time and correct part. :-)
Chrome Bezel
Timothy
June 17, 2018
It was just what I wanted and at a good price. Easy ordering process and timely delivery. Recommend
Worked Great!
M
October 22, 2018
This was exactly what I was looking for. It fit just perfect and was exactly what I was looking for. Thanks!
Tailgate handle bezel
Keith
January 11, 2019
1AAuto has very good prices. Their shipping is fast. Customer service is above and beyound what you'ld expect. Thanks for your help and continnues service. Product is great and how to videos are a great help in many instances.
Good Replacment
Alejandro
August 3, 2020
After my OEM bezel flew off I needed a replacement. This is a good replacement although my order got lost in transit and I had to reach out to customer service. Happy with my new Bezel!
Chrome Tailgate Bezel
Michael
March 4, 2022
The quality seems good. It had a blemish in the chrome plating on the inside that isnt too noticeable, almost like oil from a thumb that wasnt wiped off when it got chrome plated. I decided to keep and use than rather to call for an exchange or replacement. Shipping was swift. This is the reason of the 4 outta 5 stars.
Customer Q&A
Looking for chrome tailgate bezel with center hole for lock, can you let me know if you'll have one? Thank you.January 4, 2019
Mike G
10
This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. Feel free to email or call us and we will be happy to assist.
January 5, 2019
Peter L
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
GMC is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by GMC or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.