1ASLF00353-1999-04 Honda Odyssey Front Driver Side Lower Control Arm with Ball Joint
false

Replaces

1

1999-04 Honda Odyssey Front Driver Side Lower Control Arm with Ball Joint TRQ PSA84072


99-04 Honda Odyssey Front Lower Control Arm w/Balljoint LF
$ 79.95
$99.95
20% OFF
$99.95
20% OFF
FREE SAME DAY SHIPPING
TRQ
PSA84072
In Stock
Part 1ASLF00353

Orders must be placed by 2pm ET
Part 1ASLF00353
In Stock
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Description

Vehicle Fit

Warranty & Shipping
How-To & Tools

This replacement front lower control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • LH (Driver Side) FRONT LOWER
  • Replaces dealer part numbers: 51360S0XA02, 51360 S0X A02
  • Complete assembly
    • Includes ball joint & bushings
  • Direct replacement
  • Built to strict quality control standards

Worn ball joints can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace loose or worn ball joints with our quality replacement.

One way to diagnose a loose, or warn ball joint, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint for play, if it is moving you probably need to replace it.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our control arms are designed to be direct replacements for the original factory parts.  They are 100% brand new and require no modifications for installation.  No special tools are required because all of the bushings come pre-installed.

Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.

High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.

Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories.

Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, or Canada for this item.

Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories.

How to Replace Control Arm with Ball Joint 99-04 Honda Odyssey

Created on: 2013-02-18

Watch this video to learn how to replace the control arm with ball joint on your 99-04 Honda Odyssey.

  1. step 1 : Separating the Control Arm from the Knuckle
    • Loosen the lug nuts.
    • Lift the car, and remove the lug nuts the rest of the way.
    • Using pliers and a pick remove the ball joint pin.
    • Spray penetrating oil on the ball joint nut.
    • Using a wrench remove the ball joint nut.
    • Put the nut back on partially.
    • Use a ball joint fork and separate the ball joint from the lower control arm.
    • Remove the nut.
    • Pry the lower control arm out of the knuckle.
  2. step 2 : Removing the Control Arm
    • Spray the bolts on the control arm with penetrating oil.
    • Remove the two bolts from the control arm.
    • Pull the control arm down and out.
  3. step 3 : Replacing the Control Arm
    • Replace the rear bolt partially.
    • Rotate the control arm into place and push the ball joint into the knuckle.
    • Pry the control arm up to align the holes and replace the bolt.
    • Replace the ball joint nut.
    • Replace the pin.
    • Jack up the ball joint end of the control arm until all the support is on the suspension.
    • Torque the control arm bolts to 90 – 95ft/lbs.
    • Lower the control arm jack.
    • Put the wheel in place and replace the lug nuts.
    • Lower the vehicle and torque the lug nuts to 95 – 100ft/lbs. in a crossing pattern.

Tools needed for replacement

  • General Tools

    Hammer

    Jack Stands

    Pick

  • Materials, Fluids, and Supplies

    Rust Penetrant

  • Ratchets & Related

    A Piece of Pipe (for leverage)

    Ratchet

    1/2 Inch Breaker Bar

  • Screwdrivers & Related

    Pry Bar

  • Sockets - Metric

    19mm Socket

  • Specialty Tools

    Pickle Fork

  • Wrenches - Metric

    17mm Wrench

    18mm Wrench

Installation Video
Watch video

Fits these Makes

Year Make Model Description
1999-2004Honda Odyssey Honda Odyssey Front Driver Side Lower Control Arm with Ball Joint

Part Interchange

Brand Label Part Number
ACDelco 45D3443
Beck / Arnley 102-5683
Beck / Arnley 101-5684
Beck / Arnley 101-5683
Beck/Arnley 102-5683
Beck/Arnley 101-5683
Beck/Arnley 101-5684
CARQUEST CA516B
Centric Parts 623.40012
DIY Solutions SUS05629
Dorman 521-351
Dorman - OE Solutions 521-351
Dorman OE Solutions 521-351
Honda 51360S0XA02
Honda 51360SOXA02
Honda OEM 51360SOXA02
Honda OEM 51360S0XA02
Ingalls Engineering CAK620326
MAS Industries CB59003
MAS Industries CB59003PR
MOOG CK620326
MOOG RK620326
MOOG K620326
MOOG Chassis Products RK620326
MOOG Chassis Products K620326
MOOG Chassis Products CK620326
Mcquay-Norris FA4610
Mevotech CMS60103
Mevotech GS60103
Mevotech MS60103
NAPA 260-5714
NAPA Premium 2605714
Precision Driveline CB60080
Precision Driveline 5CB60080
Raybestos Chassis 507-1443
SYD 1509041

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

TRQ
PSA84072
In Stock
Part 1ASLF00353
Product Reviews
Loading reviews
5.00/ 5.0 1
Excellent Struts
Fabien
February 4, 2018
I Installed the struts assembly right front and left was a excellent fit for my Nissan Sentra. 1AAuto #1 for parts!
Customer Q&A
No questions have been asked about this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


1999-04 Honda Odyssey Front Driver Side Lower Control Arm with Ball Joint TRQ PSA84072-1ASLF00353 does not fit your:



Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.