WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Camshaft Position Sensor 2001-09 Chrysler Sebring
Created on:
Tools used
Flat Blade Screwdriver
T20 Driver
Ratchet
1. Removing the Throttle Position Sensor (TPS)
Disconnect the TPS wiring harness
Remove the two T20 Torx screws from the TPS
Pull off the TPS
2. Installing the New TPS
Put the new TPS into place
Insert the two T20 screws into the TPS
Connect the TPS wiring harness
3. Removing the Air Box
Loosen the intake hose clamp with a flat blade screwdriver
Remove the sensors from the air box
Pull the air box up and out
4. Installing the Air Box
Put the air box into place
Attach the intake hose to the throttle body
Tighten the intake hose clamp with a flat blade screwdriver
Connect the sensors to the air box
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we're going to show you how to remove and replace a throttle position sensor on this 2004 Chrysler Sebring. It has a 2.7-liter V6, and this procedure should be basically the same for any vehicle, Dodge or Chrysler, with the 2.7-liter V6 and this style throttle position sensor. The only tool you'll need is a T20 Torx driver.
The throttle position sensor is the at the back of the engine near where the intake hose comes in. Press the tab and pull the connector off. Two T20 screws hold the position sensor in place. You can see we have a socket that has a T20 Torx bit in it. We're removing those two screws. Be careful as you handle the screws; make sure you don't drop them down. Once you have the screws out, then pull them up along with the sensor.
Reinstallation of the new one's no mystery. Put it into place. Make sure it goes in properly and start the T20 screws in. Start them in by hand first. Make sure they thread correctly, then tighten them up. You don't need to have them too tight. They need to be nice and firm but don't overtighten them. Once you have those tight, make sure you reconnect the harness.
If you're going to remove your air box, loosen that clamp. There's also usually another bolt down where his forearm is that holds the air box to the frame, but you can see, you remove sensor, the hose, and then pull the air box up and out. Then we'll reinstall our air box and tighten up the clamp that holds the intake hose to the throttle body, reconnect the hose, and reconnect any of the sensors you might have disconnected.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
ESA94804
In Stock
Product Reviews
Loading reviews
4.00/ 5.02
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
1
0
0
Chrysler Sebring cam shaft sensor
David
July 23, 2019
Part fit perfectly! First time to replace so total time to replace was about 30 minutes. Great Job!! Thanks DR
Robert
January 31, 2023
Had to replace after a couple of weeks
Customer Q&A
Hi Just bought this part I have the chrysler intrepid (Canada) 2.7l DOHC motor. The original camshaft position sensor doesnt look anything like the one posted above in the ad. My question is will the one in the ad above still work or do they have to be identical in appearance?July 30, 2019
Jim S
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chrysler is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Chrysler or FCA US LLC.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.