Oxygen Sensor 101 | O2 Sensor Replacement Guide | 1A Auto

Oxygen Sensor Basics

What is an Oxygen Sensor and what does it do?

An oxygen sensor, or air fuel ratio sensor, is a device that gauges the ratio of fuel to air that the engine is receiving by measuring the amount of oxygen in the exhaust. It then feeds this information to an on board computer known as the Engine Control Unit. The Engine Control Unit adjusts the amount of fuel supplied to the engine. This is to avoid having a mixture that's either "rich," with too much fuel, or "lean," with too little fuel. Problems with the oxygen sensor can affect your fuel efficiency and your vehicle's emissions and keep your engine from running smoothly.

The purpose of the oxygen sensors is to get the engine running as closely as possible to what engineers call stoichiometric combustion or theoretical combustion, in which fuel is burned completely. For gasoline, this is an air to fuel ratio of about 14.7:1. Chemists and engineers use the Greek letter Lambda to designate the stochiometric ratio. For this reason, oxygen sensors are sometimes called lambda sensors.

The oxygen sensor determines this ratio through a chemical process that we'll only cover briefly here. After all, you came to fix your car not for a science class. Part of the O2 sensor resides inside the vehicle's exhaust system. The other part is outside the vehicle in the open air. The sensor is coated with platinum which reacts with oxygen to produce an electrical charge. The difference in charge between the inside and outside creates a voltage. That voltage carries up the wire to the ECU, which uses that info to determine the air fuel ratio and how to adjust the fuel input.

Volvo introduced automotive oxygen sensors in 1976, but they became essentially necessary in the United States in the early 1980s, with changes to the Clean Air Act. In the mid-1990s, the Clean Air Act was updated again, making additional sensors necessary. Today many cars and trucks may have as many as four O2 sensors.

How Many Should I have and where are they Located?

Since 1981, most vehicles have been manufactured with one oxygen sensor per bank of cylinders. That's one in an inline engine and two in a V-shaped engine. The banks may be named as the left and right or the front and rear depending on how the engine is mounted in the engine bay. These are located in the exhaust manifold or the exhaust pipe and are now known as upstream or pre-cat sensors, since they are located before the catalytic converter. With new emission standards, vehicles from about 1996 forward will also generally have sensors after the catalytic converter known as downstream or post-cat sensors. Some cars with single bank engines may have two sensors in each position. In general though, recent model cars and trucks will have one upstream and one downstream sensor for each bank, totaling either two or four O2 sensors.

That Covers all the Different Types, Right?

It's not quite so simple, we're sorry to say. In addition to being upstream or downstream and for one bank or the other, oxygen sensors may be narrowband or wideband. Narrowband sensors only measure if the air fuel mixture is rich, lean, or stoichiometric. The ECU must keep making small adjustments to strike the correct balance on average. A wideband sensor can make an accurate measurement of what the air fuel ratio actually is, allowing the ECU to more precisely adjust the air fuel mixture. This results in better performance and fuel economy as well as better emissions.

The number of wires in a sensor is also significant. Many early O2 sensors only used one or two wires. More recent examples will include at least three wires, with one functioning to heat the oxygen sensor. The oxygen sensor works best at a temperature of about 650 degrees Fahrenheit. Until the sensor warms up to that temperature, the ECU runs in open loop mode, where it essentially guesses what the correct fuel mix should be. When the sensor is running, there is a closed feedback loop where the ECU responds to the information to the sensor, and the sensor responds to the fuel mix dictated by the ECU. Heating the sensor allows this closed loop mode to take effect sooner, making the engine more efficient more of the time.

Oxygen sensors may also be sold as a direct fit, which will plug into a harness on the vehicle's chassis or as universal pieces which must be spliced and soldered into place. The former will obviously be easier to replace.

What can go Wrong?

Oxygen sensors have to exist in a pretty rough environment. The sensor itself is partly inside the very hot exhaust stream and is exposed to any number of different combustion byproducts. The rest of the sensor hangs out below the vehicle where it is exposed to all kinds of dirt and debris. It's no wonder that things occasionally go wrong. The sensor itself can become clogged with particulate matter or corroded by the various chemicals it encounters. The outside parts can be damaged by abrasive dirt and rocks.

If the oxygen sensor is not working properly, it can keep the engine from running at maximum efficiency. This can lead to reduced gas mileage and worse emissions. These effects may be hard to notice. Unless you are absolutely scrupulous about recording your miles per gallon, you might not notice a change in your fuel usage. The first sign that your emissions are bad will probably be a failed inspection.

There are some subtle signs that that your oxygen sensors are not functioning correctly. Faulty sensors may lead to disrupted engine timing which can cause rough idling and engine know or pinging. There is one rather obvious sign of a faulty oxygen sensor: the check engine light. Your oxygen sensor is the most likely culprit when the check engine light comes on. You could also check that your oxygen sensors are working with a digital voltmeter, if you happen to have one of those lying around.

Can I Replace my Oxygen Sensors Myself?

Replacing an oxygen sensor is doable with some effort. Because of the extreme heat in the exhaust, the sensor can become seized -practically welded - into place. If that's the case it may require extra effort to remove. The new sensor may come with some anti-seize grip that you can apply around the threading to keep that from happening next time. Be sure not to get any grease onto the sensor itself or it may not work properly. In fact, overall, you want to be very careful with the new oxygen sensor since anything that gets on it or in it may impede its proper functioning. As mentioned before, universal sensors will take more time to install since they must be spliced to the vehicle's wiring, instead of plugging in directly.

Need an Oxygen Sensor Replacement?

If you are in need of an oxygen sensor replacement, you have come to the right place. 1A Auto not only knows everything about car and truck O2 sensors, but we stock the highest quality, most dependable aftermarket oxygen sensors available. We carry upstream and downstream oxygen sensors - and much more - for many cars, trucks, vans and SUVs, and at great prices!

At 1A Auto, we're here to help you get the right oxygen sensor replacement for your vehicle. You can browse our large selection of oxygen sensors and shop right here on 1AAuto.com or, if you have any questions about the product, warranty, compatibility, or simply prefer to order via phone, you can call our customer service toll free at 888-844-3393.


Over 3,500
Installation
Videos


Watch the 1A Auto Videos
We're here to help

888-844-3393

hablamos español: 866-401-3393

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY M-F
For Orders Placed By 5pm Est