Replaces
This part doesn’t fit a . Select from parts that fit.
Light Assembly Lifetime Warranty
Frequently bought together
Part Details
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Tools used
Brought to you by 1AAuto.com your source for quality replacement parts and the best service on the internet.
Hi. I'm Don from 1A Auto. I hope this how to video helps you out, and the next time you need a part for your vehicle think of 1AAuto.com. Thanks.
In this video we're going to show you how to replace a headlight assembly on a 2006 Chevy Impala. It's virtually the same for the right side and the left side as well as model years 2006 through 2012. In order to do this you'll need a 7mm socket and socket wrench as well as a new headlight assembly from 1A Auto. We'll also show you how to service the bulbs inside the headlight assembly as well. We're going to be doing the driver side headlight, it's basically the same for the passenger side.
Locate the one 7mm fastener right there, as well as the white clip right there. I'm using a 7mm deep socket with a socket wrench to remove that fastener there. I'll go ahead and fast-forward as I do that. Once you got that out, go ahead and pull upon that white bar, and pop it off the two hooks on the back of the headlight assembly. Go ahead and pull out your headlight assembly.
In this clip here, we're going to show you how to service the bulbs, and their all pretty much the same style of installation. In taking it out, you're just going to twist the bulb socket out of the housing, and once you get them out, you're going to pull the bulbs out. Disconnect them from the harness, and that's true for all the bulbs there. See, this one just pulls right out and snaps back in. The high-beam and low-beam which are the next two bulbs are behind two plastic covers. Those are the same where you have to turn them to the left, and once you do that you'll be able to access the bulb and the harness. It's probably easier if you unclip the harness first, and then twist the bulb out. It's going to go back in. It's got three prongs. They need to line up with the housing of the headlight assembly. Once you've done that, twist it, tighten it, and clip your harness back in. It's going to be the same for the next bulb. The last bulb is going to be just like the first where you twist it out and pull the bulb from the socket.
If you're looking to replace the whole headlight assembly go ahead and disconnect your connector. Here's a side-by-side of the old part that's faded and pitted, and then the new part from 1A Auto that you see has a perfectly clear lens. It's ready to be installed just as it is. To reinstall, first plug in your harness to the connector on the back of the headlight assembly. Then I found that it's easiest to line up the three tabs or recognize that there's two there that go in those slots, and that one on the back. That goes into the inner fender well. If you put the bottom in first, it's a little bit easier. You can see I'm kind of having trouble with it right there. If you slide in the bottom first it should go ahead and fit right in just like that. Go ahead and reinstall that 7mm screw. I'll fast-forward as I do that. Now go ahead and take that white long clip that you took out. Align it over that taps of the hooks that went on the back side of the headlight assembly and push down.
We hope this helps you out. Brought to you by www.1AAuto.com. You source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
