Correct depression/mounting area for the OE Emblem
Direct replacement
Built to strict quality control standards
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Install Tip: Keep & reuse your original hardware, new hardware is not included with this item.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Liftgate Handle Garnish 2010-15 Toyota Prius
Created on:
Tools used
Soapy Water
Socket Extensions
10mm Socket
Ratchet
Trim Tool Set
Pick
1. Remove the Tailgate Panel
Pry off the top panel with a trim tool
Pop the side trims off with a trim tool
Pop off the bottom trim with a trim tool
Pry off the middle trim with a trim tool
2. Removing the Outer Trim
Remove the 10mm nuts from the outer trim
Pry out the outer trim with a trim tool
Slide the handle out of the outer trim
3. Installing the Outer Trim
Line up the studs on the outer trim with the holes on the hatch
Press the outer trim into place
Tighten the 10mm bolts to the outer trim
With soapy water and a pick, pull the weatherstripping out beneath the window so it's realigned
4. Installing the Tailgate Panel
Press the middle trim into place
Press the lower trim into place
Press the side trims into place
Press the upper trim into place
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
To remove the rear hatch trim, we'll have to start at the top piece here. Use your plastic prying tool. You can buy these from 1AAuto.com. Slide it underneath here. Pop it out. It's going to snap. Just get it started. Got four clips. If a clip stays behind, it’s not a big deal. You use this part of the tool or this part of the tool. Slide it underneath here. Pop it out, and it can be reused by simply pushing it back in here. Put that aside. Now we pop this side trim off. This will be the same for both sides. You usually get started like this. It'll pop right off. Un-clip it from this lower one. The same for the other side.
The middle piece is not the next piece. It's actually last. We can do the bottom part here. Use a plastic prying tool, a narrow one. There's a small cutout slot here. I'm going to get in here underneath it. Pop it off the clips. Pull it down. Work your way around it. They're in here. With some significant force, you got to put on it to pull it out. Work your way all the way around, using the plastic prying tool to help you take them off. Do the same on this side. Pry it down. Separate it from this middle panel. Try to pull forward and up with a good amount of force.
You're trying to separate it from these little pull handle cups, going to slide behind the metal. Pop it off from this panel here. This seemed to have broken off, but it really didn't. You can just push it back into place because, once it's inside, the panel holds it up against it, and then you reach in and grab it so it won't come apart once it's in there.
Now, with the lower and the upper panels removed, we can get to the center panel. Start to pull it down. It just un-clips it. Just un-clip it. These clips are, some good tension to them so I'm going to really pull on it. With all these trim panels off, you can get to the rear washer nozzle, you can get to the rear wiper motor.
These are your connections, where they defrost on this lower piece of glass and then the defrost on the upper piece of glass, you need to make repairs there. You can also reach the rear connector for your door handle and all the bolts and the nuts for your rear trim panel. The plate lights are accessible through openings in the trims. You don't have to take off the trim, but you can see them in here and, of course, all your wiring harnesses that are in here.
To remove this trim here and get to your license plate lights and your hatch electric handle, lift up the opening and, with the trim removed, there's a stud here with a 10-millimeter nut on it and another one on the other side. There's also two nuts and two studs right in the center by the door lock handle. Remove those. Remove this nut. The same for this side. Use my plastic prying tool. You can get this from 1AAuto.com.
Going to pry the trim off because it's clipped on. Lot of dirt under here. Work my way across. You work your way across. You pull it off the clips. I'm going to slide the whole thing out. Should have actually put that on the inside, but this handle will slide off these studs here, just like that. Panel off.
Put our trim panel back on. These two studs need to go in these two openings here, and then these two over here, and then the clips will just push in. I'm going to line up these longer ones first in the middle. Get the other ones lined up. Push through. There is a rubber piece of trim here. It's okay. Get them lined up. Clip them in, just like that. Pull this rubber trim back out, a little bit of glass cleaner.
Use a right angle pick and just carefully start this little weatherstrip. Pull it out. Using some soapy water, carefully using the right angle pick, just pull this weather strip out. Going to reinstall the 10-millimeter nuts. The same for all four of them. Reinstall the middle trim piece first. There's four clips along the inside here. Slide it up into position. Clip it in place. Going to reinstall the lower part. Does have some tabs here and here. They're going to fit into the openings here and here on this center trim piece. These pull handles that are on the panel, they come up and they hook into the sheet metal here. Get into position. I'm going to go in this way with it. Slide it in. Push it back in on the clips. Trim panel's reinstalled.
Going to reinstall the two side pieces. These install the same exact way for both sides. Line them up to here. Push the clips into place. Do the same for the other one. Reinstall the center piece. This key, there's a wide part that fits in this wide opening here, and then two pieces here that fit over here so you don't have to try and install it backwards. It won't fit. These will need to line up with the corresponding openings. Trim is reinstalled.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
BHS00131
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Toyota is a registered trademark of Toyota Motor Corporation. 1A Auto is not affiliated with or sponsored by Toyota or Toyota Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.