Specifications:

  • Brand New Hub & Axle Kit
  • Comes as a 2 Piece Kit
    • Both LH (Driver Side) or RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:40)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts in a crossing or star pattern
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Rotor (1:21)
    • Remove the 17mm bolts from the brake caliper while using an 18mm wrench to hold the inside nut
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
    • If the rotor will not come off hit the rotor with a ball peen hammer
    • If the rotor still won't come off, thread the bolts into the press holes and slide the rotor off
    • Remove the center hub nut
    • Hit the Axle with a hammer
  3. step : Removing the Hub (3:30)
    • Disconnect the clips on the harness on the upper control arm
    • Disconnect the wiring harness
    • Spray each side of the hub with penetrating oil
    • Remove the three 18mm bolts holding the hub
    • Hammer the back of the hub to loosen it
    • Pull the harness through and remove the hub
    • Hammer the backing plate off the hub
  4. step : Installing the New Hub (5:35)
    • Feed the harness through the backing plate
    • Place the backing plate into place
    • Push the hub onto the axle and into place
    • Place an 18mm bolt to hold the plate and hub to the wheel knuckle
    • Replace and tighten the 18mm bolts
    • Torque the 18mm bolt to 90 ft/lbs
    • Clip the wiring harness to the steering wheel knuckle
    • Connect the wiring harness
  5. step : Installing the Rotor (7:31)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Apply brake grease to the caliper bracket bolts
    • Put the bracket back into place
    • Start the 18mm bolts by hand and tighten them
    • Torque the bolts to 110 ft/lbs of torque
    • Install the new brake pads into the bracket
    • Apply brake grease to the brake pads
    • Put the caliper on
    • Thread the 17mm bolts by hand
    • Torque bolts to 40 ft/lbs
    • Replace the hub nut and remove the lug nut
  6. step : Reattaching the Wheel (9:16)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap
  7. step : Testing the Brakes (10:11)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 35mm Socket
  • 19mm Socket
  • 18mm Socket
  • 17mm Socket

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
solved problem
The Auto Zone Brg. only lasted 1 yr. /better quality
December 9, 2017
Purchased
3 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(10:42 min)

Tools List:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 35mm Socket
  • 19mm Socket
  • 18mm Socket
  • 17mm Socket

  • Wrenches - Metric

  • 18mm Wrench



This part replaces:

  • Reference Number 513188
  • Dorman 4110377
  • Hollander 538-01587
  • OE # 12413037, 15130858

Vehicle Fit

  • 2004-2007 Buick Rainier Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2002-2009 Chevy Trailblazer Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2002-2006 Chevy Trailblazer EXT Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2002-2009 GMC Envoy Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2002-2006 GMC Envoy XL Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2004-2005 GMC Envoy XUV Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2003-2008 Isuzu Ascender Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2002-2004 Olds Bravada Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
  • 2005-2009 Saab 9-7X Front Wheel Hub Bearing & Axle Kit 2 Piece Set Driver or Passenger Side
Part #: 1AAHK00020

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More