Replaces

Wheel Bearing & Hub Assembly TRQ BHA53658 - 1ASHS00617

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Ball Bearing
  • Quantity: 4 Piece Set

Specifications:

  • Comes as a SET of 4
    • (2) - FRONT Hubs with 3 Bolt Triangular Flanges - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Hubs with 4 Bolt Rectangular Flanges - LH (Driver Side) & RH (Passenger Side)
  • Fit 5 Lug Wheels
  • Replaces dealer part numbers: 12403095, 7467357, 7467587, 12413093, 12413094, 12413125, 12413126, 12413194, 88964168, 88964177
  • Studs already installed
  • Built to strict quality control standards
  • Fit models with ABS - RPO Code "JL9"
  • Have ABS sensors built in with correct plug configuration
  • Fit FWD (Front Wheel Drive) Models only
    • Do NOT fit AWD (All Wheel Drive) Models

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:59)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:23)
    • Remove the two 14mm bolts from the brake caliper
    • Pull the caliper aside
    • Pull the brake pads off
  3. step : Removing the Brake Rotor (2:04)
    • Remove the two 13mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Hold the rotor in place with a flat blade screwdriver
    • Remove the T30 Torx screw from the rotor
    • Strike the rotor with a hammer to loosen it
    • Pull the rotor off
  4. step : Removing the Wheel Hub (3:16)
    • Remove the four 10mm bolts from the wheel hub
    • Disconnect the ABS wiring harness from the hub
    • Strike the hub with a hammer to remove it
    • Push out the emergency brake cable pin with a hammer and a screwdriver
    • Pull the spring off the brake backing plate with a screwdriver
    • Pull the emergency brake cable out of the brake backing plate
  5. step : Separating the Wheel Hub from the Brake Backing Plate (5:01)
    • Remove the two T30 screws from the backing plate
    • Pull the bracket off of the backing plate
    • Pull the backing plate off of the hub
    • Pull the emergency brake ring off of the hub
  6. step : Preparing the New Wheel Hub (5:35)
    • Clean the hub mounting area with a wire brush
    • Apply white grease or bearing grease to the mounting area
    • Put the emergency brake ring onto the backing plate
    • Put the hub through the ring and backing plate, making sure the ABS wiring connector is lined up with the backing plate hole
    • Pull the arm off the emergency brake activator
    • Put the emergency brake activator onto the ring
    • Attach the bracket to the backing plate
    • Insert the two T30 screws into the bracket
    • Push the emergency brake arm into place through the bracket
  7. step : Installing the New Wheel Hub (7:39)
    • Attach the emergency brake cable to the emergency brake arm
    • Push the emergency brake cable into its bracket
    • Insert the pin into the bracket, using a hammer
    • Attach the spring to the emergency brake arm
    • Pull the spring onto the bracket with vise-grip pliers
    • Push the hub into place
    • Start one of the 10mm bolts to hold the hub in place
    • Start the remaining three 10mm bolts
    • Tighten the four 10mm bolts to 45 - 50 foot-pounds of torque
    • Reconnect the ABS wiring harness
    • Adjust the emergency brake, by turning the wheel with a flat blade screwdriver
  8. step : Reinstalling the Brake Rotor (9:43)
    • Slide the rotor on
    • Adjust the emergency brake further, if necessary
    • Insert the T30 screw into the rotor
    • Put the bracket back into place
    • Start the two 13mm bolts by hand
    • Tighten the bolts to 75 foot-pounds of torque
  9. step : Reinstalling the Brake Pads (10:45)
    • Apply grease to the brake pads
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten bolts to 30 foot-pounds
  10. step : Reattaching the Wheel (11:27)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 14mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

4.2 / 5.0
5 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
0
0
0
1
Love the videos and parts!
Every time I work on a car and get stuck, I search through the step by step videos and 1aauto always helps me out! I have ordered parts a couple times from this company and they have earned my trust. I was concerned about buying parts online from the US as I live in Canada but there is nothing to worry about. Keep up the good work! I'll be ordering parts again when needed. Thanks so much.
September 4, 2018
Purchased
1 month ago
Very fast delivery
If I need any other parts I will deal with this company they are very fast on sending your product to you and the right part that means a lot in today's parts ordering I've ordered off of others in the past and always received the wrong part look forward to doing more business with these people
March 26, 2018
Purchased
6 months ago
Perfect fit, solved problem!!
These were a perfect fit and solved my noise issue! Local shop told me I'd have to replace the entire strut assembly for about $500 a piece, looked the hubs up here and found them to be much cheaper and easy to replace myself!
February 23, 2018
Purchased
over 3 years ago
1ashs00617 hub ass trqbha53658
Price was great hub was perfect fit for my car. Watched the video on how to install them never did this job before. Toke my time at 4 hours a wheel from the ground. Quality product. Saved a lot of money doing this job myself.
November 14, 2017
Purchased
10 months ago
Awful
Order four wheel bearings and the rears were ok. But the front pair were awful. I spent most of a day doing thwm and replacing calipers and stuff. And when i went to test drive the wiring connectors ripped right off the wheel bearing. I made sure that i installed them correctly. No twist. Not tangled or wrapped around anything and used the dust cover tie point for the plastic connector. Just disappointed because i worked so hard and invested money and then i did it for nothing.
July 26, 2017
Purchased
1 year ago
Response from 1A Auto
We are sorry to hear of your experience. Please contact us at your convenience so we may provide a proper resolution.
July 26, 2017
Alex P Staff
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Would this fit on my impala ss with 18 inch wheels?
terrance s on Dec 29, 2016
BEST ANSWER: As long as your vehicle has the RPO code JL9 and within the year range 2006 - 2008, or 2009 - 2013 then these will fit your vehicle with the 18 inch wheels.

Vehicle Fit

Year Make Model Description
2005-2008Buick Allure Buick Allure Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with ABS Brakes TRQ
2009Buick Allure Buick Allure Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
2005-2008Buick LaCrosse Buick LaCrosse Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with ABS Brakes TRQ
2009Buick LaCrosse Buick LaCrosse Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
2005Buick Terraza Buick Terraza Front Wheel Drive Front & Rear 4 Bolt Flange Wheel Bearing & Hub Assembly 4 Piece Set TRQ
2006-2008Chevy Impala Chevy Impala Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with ABS Brakes TRQ
2009-2013Chevy Impala Chevy Impala Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
2006-2007Chevy Monte Carlo Chevy Monte Carlo Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with ABS Brakes TRQ
2005Chevy Uplander Chevy Uplander Front Wheel Drive Front & Rear 4 Bolt Flange Wheel Bearing & Hub Assembly 4 Piece Set TRQ
2004-2008Pontiac Grand Prix Pontiac Grand Prix Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with ABS Brakes TRQ
2005Pontiac Montana SV6 Pontiac Montana SV6 Front Wheel Drive Front & Rear 4 Bolt Flange Wheel Bearing & Hub Assembly 4 Piece Set TRQ
2005Saturn Relay Saturn Relay Front Wheel Drive Front & Rear 4 Bolt Flange Wheel Bearing & Hub Assembly 4 Piece Set TRQ

This part replaces:

  • TRQ BHA53658
Part #: 1ASHS00617


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA53658

How-to Video:

(12:19 min)