Replaces

Wheel Bearing & Hub Assembly Timken HA590092 - TKSHR00129

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA590092

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • 4 Bolt Rectangular Flange
  • Fits 5 Lug Wheel
  • Studs already installed
  • Built to strict quality control standards
  • Fits models with ABS - RPO Code "JL9"
  • Has ABS sensor built in with correct plug configuration
  • Fits FWD (Front Wheel Drive) Models only

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:59)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:23)
    • Remove the two 14mm bolts from the brake caliper
    • Pull the caliper aside
    • Pull the brake pads off
  3. step : Removing the Brake Rotor (2:04)
    • Remove the two 13mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Hold the rotor in place with a flat blade screwdriver
    • Remove the T30 Torx screw from the rotor
    • Strike the rotor with a hammer to loosen it
    • Pull the rotor off
  4. step : Removing the Wheel Hub (3:16)
    • Remove the four 10mm bolts from the wheel hub
    • Disconnect the ABS wiring harness from the hub
    • Strike the hub with a hammer to remove it
    • Push out the emergency brake cable pin with a hammer and a screwdriver
    • Pull the spring off the brake backing plate with a screwdriver
    • Pull the emergency brake cable out of the brake backing plate
  5. step : Separating the Wheel Hub from the Brake Backing Plate (5:01)
    • Remove the two T30 screws from the backing plate
    • Pull the bracket off of the backing plate
    • Pull the backing plate off of the hub
    • Pull the emergency brake ring off of the hub
  6. step : Preparing the New Wheel Hub (5:35)
    • Clean the hub mounting area with a wire brush
    • Apply white grease or bearing grease to the mounting area
    • Put the emergency brake ring onto the backing plate
    • Put the hub through the ring and backing plate, making sure the ABS wiring connector is lined up with the backing plate hole
    • Pull the arm off the emergency brake activator
    • Put the emergency brake activator onto the ring
    • Attach the bracket to the backing plate
    • Insert the two T30 screws into the bracket
    • Push the emergency brake arm into place through the bracket
  7. step : Installing the New Wheel Hub (7:39)
    • Attach the emergency brake cable to the emergency brake arm
    • Push the emergency brake cable into its bracket
    • Insert the pin into the bracket, using a hammer
    • Attach the spring to the emergency brake arm
    • Pull the spring onto the bracket with vise-grip pliers
    • Push the hub into place
    • Start one of the 10mm bolts to hold the hub in place
    • Start the remaining three 10mm bolts
    • Tighten the four 10mm bolts to 45 - 50 foot-pounds of torque
    • Reconnect the ABS wiring harness
    • Adjust the emergency brake, by turning the wheel with a flat blade screwdriver
  8. step : Reinstalling the Brake Rotor (9:43)
    • Slide the rotor on
    • Adjust the emergency brake further, if necessary
    • Insert the T30 screw into the rotor
    • Put the bracket back into place
    • Start the two 13mm bolts by hand
    • Tighten the bolts to 75 foot-pounds of torque
  9. step : Reinstalling the Brake Pads (10:45)
    • Apply grease to the brake pads
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten bolts to 30 foot-pounds
  10. step : Reattaching the Wheel (11:27)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 14mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2008 Buick Allure Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Driver or Passenger Side Timken HA590092
  • 2009 Buick Allure Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2004-2005 Buick Century Rear Wheel Bearing & Hub Assembly Driver or Passenger Side for Models with ABS Brakes Timken HA590092
  • 2005-2008 Buick LaCrosse Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Driver or Passenger Side Timken HA590092
  • 2009 Buick LaCrosse Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 1997-2002 Buick Regal Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2003-2004 Buick Regal Rear Wheel Bearing & Hub Assembly Driver or Passenger Side for Models with ABS Brakes Timken HA590092
  • 2005 Buick Terraza Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Driver or Passenger Side Front Wheel Drive Timken HA590092
  • 2000-2005 Chevy Impala Rear Wheel Bearing & Hub Assembly Driver or Passenger Side for Models with ABS Brakes Timken HA590092
  • 2006-2008 Chevy Impala Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Driver or Passenger Side Timken HA590092
  • 2009-2013 Chevy Impala Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2014-2016 Chevy Impala Limited Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2000-2002 Chevy Monte Carlo Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2003-2005 Chevy Monte Carlo Rear Wheel Bearing & Hub Assembly Driver or Passenger Side for Models with ABS Brakes Timken HA590092
  • 2006-2007 Chevy Monte Carlo Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Driver or Passenger Side Timken HA590092
  • 2005 Chevy Uplander Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Driver or Passenger Side Front Wheel Drive Timken HA590092
  • 2002-2005 Chevy Venture 2 Wheel Drive Rear Wheel Bearing & Hub Assembly for Models with Rear Disc Brakes Driver or Passenger Side Timken HA590092
  • 1998-2002 Olds Intrigue Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2001-2002 Pontiac Aztek 2 Wheel Drive Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2003-2005 Pontiac Aztek 2 Wheel Drive Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Driver or Passenger Side Timken HA590092
  • 1997-2002 Pontiac Grand Prix Rear Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590092
  • 2003 Pontiac Grand Prix Rear Wheel Bearing & Hub Assembly Driver or Passenger Side for Models with ABS Brakes Timken HA590092
  • 2004-2008 Pontiac Grand Prix Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Driver or Passenger Side Timken HA590092
  • 2002-2005 Pontiac Montana 2 Wheel Drive Rear Wheel Bearing & Hub Assembly Driver or Passenger Side for Models with Rear Disc Brakes Timken HA590092
  • 2005 Pontiac Montana SV6 Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Driver or Passenger Side Front Wheel Drive Timken HA590092
  • 2005 Saturn Relay Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Driver or Passenger Side Front Wheel Drive Timken HA590092

This part replaces:

  • Timken HA590092
  • OE # 12403095
  • OE # 122413091
  • Hollander 538-01635
  • OE # 88964177
Only 4 left in stock
Part #: TKSHR00129

Timken
Brand #: HA590092

How-to Video:

(12:19 min)