Replaces

Wheel Bearing & Hub Assembly Rear TRQ BHA54224 - 1ASHR00090

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
      Direct Fit Replacement
      Precision Engineered
      Highest Quality Materials
  • Bearing Type:   Ball Bearing
  • Front or Rear Location:   Rear

Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • Direct replacement
  • Replaces dealer part numbers: 12413117, 12413118, 12413206, 42200SV7C61, 22706424, 7467596
  • Fits 5 Lug Wheel
  • Studs already installed
  • Built to strict quality control standards
  • Fits models without ABS (Anti Lock Brakes)

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:53)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap by hand
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:16)
    • Remove the two 14mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (2:11)
    • Remove the two 15mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  4. step : Removing the Wheel Hub (2:34)
    • Remove the four 15mm nuts from the wheel hub
    • Strike the wheel hub with a hammer to loosen it
    • Disconnect the ABS sensor if necessary
    • Clean the wheel hub mounting area with a wire brush
  5. step : Installing the New Wheel Hub (3:50)
    • Put the new wheel hub into place while holding the backing plate
    • Connect the ABS sensor if necessary
    • Fasten the four 15mm nuts onto the wheel hub
    • Tighten the 15mm nuts to 65 foot-pounds of torque
  6. step : Reinstalling the Brake Rotor (4:28)
    • Slide the rotor on
    • Put the bracket back into place
    • Start the two 15mm bolts by hand
    • Tighten the 15mm bolts to between 50 to 55 foot -pounds
  7. step : Reinstalling the Brake Pads (4:46)
    • Apply brake grease to the brake pad slides
    • Install the brake pads into the bracket
    • Line up the caliper piston with the brake pad notch
    • Put the caliper on
    • Thread the 14mm bolts by hand
    • Tighten the 14mm bolts to between 60 to 65 foot-pounds
  8. step : Reattaching the Wheel (6:28)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket
  9. step : Testing the Brakes (7:02)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Hammer
  • Wire Brush
  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • White Grease

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench
  • Swivel

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 14mm Socket
  • 15mm Socket
  • 13mm Socket

  • Wrenches - Metric

  • 19mm Wrench

  • Wrenches - SAE

  • 13/16 Inch Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2006-2009Chevy HHR Chevy HHR Rear Wheel Bearing & Hub Assembly without ABS Brakes TRQ
2004-2005Chevy Malibu Chevy Malibu Rear Wheel Bearing & Hub Assembly New Body Style (4th Vin Digit Z) without ABS Brakes TRQ
2006-2008Chevy Malibu Chevy Malibu Rear Wheel Bearing & Hub Assembly without ABS Brakes TRQ
2004-2007Chevy Malibu Maxx Chevy Malibu Maxx Rear Wheel Bearing & Hub Assembly without ABS Brakes TRQ
2005-2007Pontiac G6 Pontiac G6 Rear Wheel Bearing & Hub Assembly without ABS Brakes TRQ
Part #: 1ASHR00090


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA54224

How-to Video:

(07:26 min)