Replaces

Wheel Bearing & Hub Assembly Pair Front Timken 513124 - TKSHS00003

TIMKEN HUB ASSEMBLY: 513124 (PAIR)

Specifications:

  • Brand New Timken Hub Assemblies
  • Comes as a PAIR:
    • Includes both the RH (Passenger) & LH (Driver) side FRONT
  • Direct replacement
  • Replaces OE# 12413045
  • Fits Four Wheel Drive and All Wheel Drive
  • Fits RH or LH FRONT
  • Has ABS sensor
  • Built to strict quality control standards

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel and tire (1:00)
    • Loosen your hub nut with your 35 mm socket.
    • Loosen your lug nut with your 19 mm lug wrench.
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel, remove the hub nut.
  2. step : Remove Brake Caliper (2:17)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 18 mm socket wrench to remove the caliper bolts.
    • Use a wrench to pry the caliper off.
    • Use a wire tie to help prevent stress on the caliper.
  3. step : Remove Brake Rotor (2:58)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (3:04)
    • Remove the clips for the hub harness.
    • Use a screwdriver to unclip the hub harness.
    • Unbolt the hub harness.
    • Remove the 3 bolts securing the hub using your 18mm socket and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Remove the hub, using driving tools to help work it out of the steering knuckle.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (6:45)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18mm bolts in place and tighten the nuts to 65 ft lbs.
  6. step : Put brakes and wheel back on (6:45)
    • Refer to our other videos for more detailed instructions.
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 95 ft lbs
    • Hub nut is 75 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to have the vehicle aligned.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 11mm Socket
  • 12mm Socket
  • 13mm Socket
  • 14mm Socket
  • 15mm Socket
  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket

  • Wrenches - Metric

  • 13mm Wrench
  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2005 Chevy Blazer S10 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124
  • 1998-2004 Chevy S10 Pickup 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124
  • 1998-2000 GMC Envoy 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124
  • 1997 GMC Jimmy S-15 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124
  • 1998-2001 GMC Jimmy S-15 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124
  • 1998-2004 GMC S-15 Sonoma 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124
  • 1998-2000 Isuzu Hombre 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124
  • 1997-2001 Olds Bravada 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair Timken 513124

This part replaces:

  • Timken 513124
Only 2 left in stock
Part #: TKSHS00003



Timken
Brand #: 513124

How-to Video:

(07:28 min)