Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Frequently bought together
Specify your vehicle's year, make and model to guarantee fit.
If your vehicle isn't listed, search Brake Kits
Part Details
TRQ brake kits are designed to restore your brake system to like-new performance. TRQ brake pads are positive molded, thermal scorched, chamfered, and utilize a multi-layer shim for enhanced performance and service life. TRQ rotors have a non-directional finish that reduces the break-in period for new rotors as well as reducing vibrations throughout the rotor’s lifecycle. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the rear brakes on this 2004 Volkswagen Jetta and we show you on the passenger side, but the driver's side is the same procedure. The items you'll need for this are new brake pad and rotor kit form 1AAuto.com, 13mm and 18mm socket and ratchet with a piece of pipe for leverage, 7mm and 8mm Allen bit or wrenches, flat blade screwdriver, jack and jack stand, torque wrench, wire brush, large C-clamp, mineral spirits, or brake cleaner, brake grease, and a pry bar.
Start off using a 7mm Allen bit or wrench and just pry out these lug cap covers, and we'll fast forward as Don does the rest of them. You'll notice that one of these lug bolts is slightly different and it's rounded. You're going to need a key to remove this and the key can be found right here in the trunk, right next to your jack. We'll just push it into place and now it will remove like all the other lug nuts. If you don't have air-powered tools, you're going to want to loosen these while the vehicle is on the ground. Then raise the vehicle and remove them the rest of the way. If the wheel doesn't pull off once they're all removed, just twist another lug bolt back in, and then use a pry bar from behind and just hit the wheel out. Now you can just remove that lug bolt, and your wheel is free.
Now you can inspect your brakes. You can check the rotor, check for any deep grooves, and you can look through here to see how much life is on your brake pads.
To remove this caliper, you need to remove these two 13-mm bolts on the back and we'll fast forward as Don does that. Using a flat blade screwdriver, pry the brake pad back into the piston to help remove the caliper a little bit. Now you can just pry the caliper off, and just set it aside, and remove your brake pads.
Now, remove these two 8mm Allen bolts. We'll fast forward as Don does that. Once those are removed, you can pull your caliper bracket off. We need to remove the screw if you still have one there holding the rotor in. It's going to take some force usually, and worst case scenario, you could actually just use a drill and drill the head off, and then remove the disk. It's not necessary for re-installation.
Using a large C-clamp, you just want to apply some pressure to the piston on the caliper and then use your pliers to just twist the piston back into place. You'll notice after a while that the C-clamp will become loose and just tighten it up again, and then start twisting again. You just want to repeat this process until the piston is back in place, and we'll just fast forward as Don does this.
Using mineral spirits or break cleaner, clean up your rotor whether it's old or new, and using a wire brush, just clean the slides where the brake pads go on your caliper bracket, and check these slides and make sure they move in and out. If they don't, pull them all the way out and grease them up again. Then apply some brake grease to the tabs on either side of your brake pads.
Push your rotor into place and replace that Phillips screw. We'll just fast forward as Don does this. Now put your brake caliper bracket back into place and just replace those 8mm Allen bolts, and we'll fast forward as Don replaces and tightens them up. You want to torque these to about 50 foot-pounds.
Now push your brake pads into place and then fit your caliper up over them and into place on the caliper bracket, making sure that those slides go underneath and into place for the bolts to go through, and we'll fast forward as Don replaces those two 13mm bolts and tightens them up.
Now replace your wheel and those lug bolts and just tighten them up. If you don't have air-powered tools, tighten them preliminarily, then, lower the vehicle and tighten them the rest of the way. Now with your vehicle on the ground, just torque each of those lug bolts to 100 foot-pounds. We'll fast forward as Don replaces those lug bolt caps. Now pump your brakes until they firm up and then do a brake test from 5 mph and then 10 mph. Then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front brakes on this 2004 Volkswagen Jetta. We show you on the passenger side, but the driver's side is the same procedure. The items you'll need for this are: a new brake pad and rotor kit from 1AAuto.com, 18mm socket and ratchet with a piece of pipe for leverage, 7mm Allen bit, flat blade screwdriver, jack and jack stands, torque wrench, wire brush, large C-clamp, mineral spirits or brake cleaner, brake grease, and a hammer.
Start off using a 7mm Allen bit, and just prying out these lug nut caps. We'll fast forward as he does the rest of those. You'll notice that this lug nut is a little different than the others. You're going to need a key to remove it, and that key can be found right here, next to your jack stand in your trunk. You can just push it into that lug nut, and now it removes just like a regular lug nut. If you don't have air-powered tools, you're going to want to loosen up these lug nuts, then raise the vehicle, and remove them the rest of the way. Once the lug nuts are removed, the wheel will pull right off.
Now, you can inspect the brakes. Run your finger on the rotor, and make sure there are no deep grooves. This rotor's in really rough shape. You can see how bad that is. The pads are almost new, probably about 60% life left, so somebody just replaced the pads, but did not resurface the rotors. So you need to replace both the pads and the rotors.
Pry out this retaining wire. Then, pry off these caps. Inside here, you'll see that there are two 7mm Allen bolts. You just want to go ahead and remove those. Now using a flat blade screwdriver, just pry your brake pad into the caliper, and this will push the caliper piston in, and make it easier to remove. Then, it just pulls off and you can set it aside. Then, you just pull out your brake pads.
Now, remove these two 18-mm bolts that hold on your caliper bracket, using a socket and ratchet, and a piece of pipe for leverage. You really just need the pipe to break the bolts free, and then it's pretty easy. Once those are removed, the bracket will pull right off. Then you want to remove this Phillips screw. It can be in there pretty good. It can take a little bit of effort to get it going. If you have one, you may want to use an impact driver, or if worse comes to worse, you can drill the head off, and then just remove the rotor. To remove that, if the rotor didn't pull off, just twist it back in a couple turns, and then hit your rotor with a hammer. Then remove that screw, and pull your rotor off.
On the left is the old rotor and brake pads. On the right are the new ones from 1A Auto. You can see they're identical, and they're going to fit exactly the same. Using brake cleaner or mineral spirits, just wipe down your new rotor. Using a wire brush, you just want to clean off the slides on your caliper bracket. Then, apply some brake grease to these tabs on either end of the brake pad.
Now, push your rotor back into place, and replace that Phillips screw. Turn the rotor so that you have more room, and just slide the bracket back into place, and replace those two 18mm bolts. If you have to drill off that screw that holds the rotor on, you can hold the rotor in place with a lug bolt during these steps. We'll just fast forward as Don tightens those up. Now torque both of these bolts to 70 foot pounds.
Using a large C-clamp, just push that piston on your caliper in the rest of the way, and then push your brake pad into place, and your other brake pad into place on the caliper bracket, and then put your caliper down into place. Then re-tighten the Allen bolts, and you'll want to tighten those to 25 to 30 foot pounds. Replace these caps, and then put the retaining wire back into place. You want to make sure that it's all the way back in.
Push the wheel back into place, and line up the holes for the lug bolts, and then replace the lug bolts. If you don't have air-powered tools, you want to tighten these preliminarily, lower the vehicle, and then tighten them the rest of the way. Then, lower the vehicle and torque each lug nut to 100 foot pounds in a crossing pattern. Now, replace your lug nut caps. Now, pump the brake until it firms up, and then you want to do a stopping test from 5 miles per hour, and 10 miles per hour. Then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
Tools used
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front brakes on this 2004 Volkswagen Jetta. We show you on the passenger side, but the driver's side is the same procedure. The items you'll need for this are: a new brake pad and rotor kit from 1AAuto.com, 18mm socket and ratchet with a piece of pipe for leverage, 7mm Allen bit, flat blade screwdriver, jack and jack stands, torque wrench, wire brush, large C-clamp, mineral spirits or brake cleaner, brake grease, and a hammer.
Start off using a 7mm Allen bit, and just prying out these lug nut caps. We'll fast forward as he does the rest of those. You'll notice that this lug nut is a little different than the others. You're going to need a key to remove it, and that key can be found right here, next to your jack stand in your trunk. You can just push it into that lug nut, and now it removes just like a regular lug nut. If you don't have air-powered tools, you're going to want to loosen up these lug nuts, then raise the vehicle, and remove them the rest of the way. Once the lug nuts are removed, the wheel will pull right off.
Now, you can inspect the brakes. Run your finger on the rotor, and make sure there are no deep grooves. This rotor's in really rough shape. You can see how bad that is. The pads are almost new, probably about 60% life left, so somebody just replaced the pads, but did not resurface the rotors. So you need to replace both the pads and the rotors.
Pry out this retaining wire. Then, pry off these caps. Inside here, you'll see that there are two 7mm Allen bolts. You just want to go ahead and remove those. Now using a flat blade screwdriver, just pry your brake pad into the caliper, and this will push the caliper piston in, and make it easier to remove. Then, it just pulls off and you can set it aside. Then, you just pull out your brake pads.
Now, remove these two 18-mm bolts that hold on your caliper bracket, using a socket and ratchet, and a piece of pipe for leverage. You really just need the pipe to break the bolts free, and then it's pretty easy. Once those are removed, the bracket will pull right off. Then you want to remove this Phillips screw. It can be in there pretty good. It can take a little bit of effort to get it going. If you have one, you may want to use an impact driver, or if worse comes to worse, you can drill the head off, and then just remove the rotor. To remove that, if the rotor didn't pull off, just twist it back in a couple turns, and then hit your rotor with a hammer. Then remove that screw, and pull your rotor off.
On the left is the old rotor and brake pads. On the right are the new ones from 1A Auto. You can see they're identical, and they're going to fit exactly the same. Using brake cleaner or mineral spirits, just wipe down your new rotor. Using a wire brush, you just want to clean off the slides on your caliper bracket. Then, apply some brake grease to these tabs on either end of the brake pad.
Now, push your rotor back into place, and replace that Phillips screw. Turn the rotor so that you have more room, and just slide the bracket back into place, and replace those two 18mm bolts. If you have to drill off that screw that holds the rotor on, you can hold the rotor in place with a lug bolt during these steps. We'll just fast forward as Don tightens those up. Now torque both of these bolts to 70 foot pounds.
Using a large C-clamp, just push that piston on your caliper in the rest of the way, and then push your brake pad into place, and your other brake pad into place on the caliper bracket, and then put your caliper down into place. Then re-tighten the Allen bolts, and you'll want to tighten those to 25 to 30 foot pounds. Replace these caps, and then put the retaining wire back into place. You want to make sure that it's all the way back in.
Push the wheel back into place, and line up the holes for the lug bolts, and then replace the lug bolts. If you don't have air-powered tools, you want to tighten these preliminarily, lower the vehicle, and then tighten them the rest of the way. Then, lower the vehicle and torque each lug nut to 100 foot pounds in a crossing pattern. Now, replace your lug nut caps. Now, pump the brake until it firms up, and then you want to do a stopping test from 5 miles per hour, and 10 miles per hour. Then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Brake Kits