Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a Set of 6
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Quantity: 6 Piece Set
  • Kit Includes: (2) Front Strut & Spring Assemblies

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Checking the Stabilizer Link (0:34)
    • Turn the wheels to the side
    • Try to shake the stabilizer link by hand
    • If the link clunks or rattles, it should be replaced
  2. step : Removing the Wheel (1:32)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Stabilizer Link (1:57)
    • Apply penetrating oil to the stabilizer link bolts
    • Insert a 6mm Allen wrench into the upper stabilizer link bolt
    • Remove the upper 17mm nut from the stabilizer link
    • Insert a 6mm Allen wrench into the lower stabilizer link bolt
    • Remove the lower 17mm nut from the stabilizer link
    • Pull off the stabilizer link
  4. step : Installing the New Stabilizer Link (4:01)
    • Put the stabilizer link into place, starting at the bottom
    • Insert a 6mm Allen wrench into the lower stabilizer link bolt
    • Tighten the lower 17mm nut onto the stabilizer link
    • Insert a 6mm Allen wrench into the upper stabilizer link bolt
    • Tighten the upper 17mm nut onto the stabilizer link
  5. step : Reattaching the Wheel (5:23)
    • Slide the wheel into place, using the locating hole
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds of torque in a crossing or star pattern

Tools needed for replacement:

    Allen Wrenches

  • 6mm Allen Wrench

  • General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • A Piece of Pipe (for leverage)
  • 1/2 Inch Breaker Bar
  • Torque Wrench

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 17mm Wrench

4.3 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
2
0
0
0
Struts did not have proper hardware for anti-skid wire
Overall I am satisfied with strut assemblies and tie rod ends. My one complaint with struts is the bracket to hold the brake anti-skid wire. The holes in the strut housing were not tapped to accept the screws included with the bracket. The screw were also much smaller than the hole in the strut housing. To attach the bracket I had to tap the hole and buy the correct size screws, One of the tie rod ends was missing the jam nut. I reused the old jam nut so it was not a major problem.
September 1, 2017
Purchased
1 year ago
Great value and a good fit
The new parts fit well and greatly improved the ride. The only issue was the screws provided in the kit to attach the ABS sensor cable holder to the struts did not fit. I had to use the screws from the old struts.
August 29, 2017
Purchased
1 year ago
Easy install
The parts were priced rite, and shipped fast. Exact fit easy swap with old parts.
July 8, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1993-1995Volvo 850 Volvo 850 Steering & Suspension Kit 6 Piece Set
1996-1997Volvo 850 Volvo 850 Steering & Suspension Kit 6 Piece Set (excluding R Models)
1998-2004Volvo C70 Volvo C70 Steering & Suspension Kit 6 Piece Set
1998-2000Volvo S70 Volvo S70 Steering & Suspension Kit 6 Piece Set
1998-2000Volvo V70 Volvo V70 Steering & Suspension Kit 6 Piece Set

This part replaces:

  • OE # 30714686, 31212730, 1387860
  • OE # 2715985
  • OE # 2715993
  • Moog K80983
  • Moog ES3257
  • Moog ES3256
Part #: 1ASFK04218

Out of Stock

How-to Video:

(07:00 min)