Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Light Option:   Halogen

Specifications

  • RH (Passenger Side)
  • Replaces dealer part number: 1K6-941-006-S, 1K6941006S
  • Includes lens & housing
  • Bulbs not included
  • Fits models with halogen headlights only
    • Not correct for models with HID (High Intensity Discharge) headlights
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly..

  1. step : Servicing the Bulbs (0:55)
    • Twist the low beam cover counterclockwise
    • Twist the bulb socket counterclockwise out of the light
    • Pull the bulb off of the socket
    • Push on the new bulb
    • Twist the bulb clockwise into the light
    • Twist on the low beam cover
    • Remove the headlight cover
    • Pull off the connector to disconnect it
    • Push on the wire retainer and pull it up to remove it
    • Pull the bulb off of the socket
    • Push on the new bulb
    • Put the tab down and lock the retainer in place
    • Connect the harness
    • Put the cover on
    • If you are removing the headlights go to step 2
  2. step : Removing the Grille (3:17)
    • Remove the two clips on top of the grille with a Phillips screw
    • Remove the two Phillips screws below the grille
    • Push in the tabs on the top of the grille
    • Pull up on either side of the grille
    • Remove the grille
  3. step : Loosening the Bumper Cover (4:05)
    • Remove the T25 screw from the fender
    • Remove the four T25 screws in the wheel well
    • Repeat the process on the other side
    • Remove the two T30 Torx screws on the top of the bumper
    • Remove the series of T25 screws along the bottom of the bumper
  4. step : Removing the Side Marker Light (5:10)
    • Pry out the side marker light with a flat blade screwdriver
    • Pull out the side marker light
    • Twist the bulb socket out of the light
    • Pull the bulb off of the socket
    • Repeat the process on the other side
  5. step : Removing the Bumper Cover (5:25)
    • Pull off either end of the bumper cover
    • Disconnect the side marker harness from the clip on either side
  6. step : Removing the Headlight (5:35)
    • Remove the T25 screws from the headlight bracket
    • Disconnect the headlight wiring harness
    • Pull the headlight out
  7. step : Installing the New Headlight (5:57)
    • Insert the headlight into place
    • Reconnect the wiring harness to the headlight
    • Replace the T25 screw on the top of the headlight bracket
  8. step : Adjusting the Headlight (6:22)
    • Park your car from 20 feet away on a level surface from a wall
    • Adjust the headlight by turning the bolt on the inside of the headlight
    • The light should concentrate an inch below where they sit on the car
    • Tighten the T25 screws to the headlight
    • Connect the headlight wiring harness
  9. step : Tightening the Bumper Cover (7:13)
    • Insert the bumper cover into place
    • Tighten the two T30 screws to the top of the bumper
    • Tighten the five T25 screws in the wheel well
    • Clip the side marker light harness to the bumper on either side
  10. step : Installing the Side Marker Light (7:59)
    • Push the bulb socket into the light
    • Push the side marker light into place, starting at the front
  11. step : Reinstalling the Bumper Cover (8:10)
    • Tighten the series of T25 screws along the bottom of the bumper
  12. step : Reinstalling the Grille (8:14)
    • Line up the tabs on the grille with the slots on the vehicle
    • Push the grille into place
    • Tighten the two Phillips screws below the grille
    • Tighten the two clips on top of the grille with a Phillips screw

Tools needed for replacement:

    Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Torx Drivers & Sockets

  • T25 Torx Driver
  • T30 Torx Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2007-2009Volkswagen GTI VW GTI (8th Vin Digit K) Halogen Headlight Passenger Side
2006-2009Volkswagen Golf VW Golf (8th Vin Digit K) Halogen Headlight Passenger Side
2005Volkswagen Jetta VW Jetta (8th Vin Digit K) Halogen Headlight Passenger Side
2006-2010Volkswagen Jetta VW Jetta Sedan (8th Vin Digit K) Halogen Headlight Passenger Side
2009Volkswagen Jetta VW Jetta Wagon (8th Vin Digit K) Halogen Headlight Passenger Side
2006-2009Volkswagen Rabbit VW Rabbit Halogen Headlight Passenger Side
Part #: 1ALHL01061


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(09:14 min)