1ADHS01701-Toyota Sequoia Tundra Front & Rear Interior Door Handle & Bezel Kit 8 Piece Set

Replaces

Toyota Sequoia Tundra Front & Rear Interior Door Handle & Bezel Kit 8 Piece Set TRQ

1ADHS01701

Part Details

  • Quantity: 8 Piece Set
  • Color: Fawn

This part replaces:

  • Dorman 81262
  • Dorman 81227
  • OE # 692050C030E1
  • OE # 69278AC010E0
  • OE # 692060C030E1
  • OE # 69277AC010E0
  • TRQ DHA37270
FREE SAME DAY SHIPPING
Save 23%
List: $103.95 Save: $24.00
Part 1ADHS01701
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: DHA37270

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Part Details

  • Color:   Fawn
  • Quantity:   8 Piece Set

Specifications:

  • Comes as a Set of 8
    • Fits LH (Driver Side) & RH (Passenger Side) Front & Rear
  • Smooth Fawn Finish
  • Direct replacements
  • Built to strict quality control standards

This new handle is made to the original color shade.  Due to vehicle age and fading from the sun, our new handles may not match your existing handle or bezel exactly.  If you are looking for an exact match, we recommend replacing handles in pairs or sets.

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Disconnecting the Battery (0:41)
    • Disconnect the negative battery cable with an 8mm wrench
  2. step : Removing the Door Panel (0:52)
    • Pry off the mirror base trim panel with a flat blade screwdriver
    • Pry off the window switch panel with a flat blade screwdriver
    • Disconnect the window switch wiring harness
    • Pry off the screw cover panel below the door pull with a flat blade screwdriver
    • Pry off the courtesy light with a flat blade screwdriver
    • Disconnect the courtesy light wiring harness
    • Pry off the door handle trim piece with a flat blade screwdriver
    • Pry off the screw cover panel at the top front corner of the door with a flat blade screwdriver
    • Remove the Phillips head screw at the top front corner of the door
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw below the door pull
    • Pry off the door handle bezel with a flat blade screwdriver
    • Push in the clips at the back of the door panel
    • Pull the clips out of the back door panel
    • Pry the door panel off of its clips with a putty knife or door panel clip tool
    • Remove any clips that remain in the door with needle nose pliers
    • Push those clips into the door panel
  3. step : Removing the Door Handle (4:06)
    • Slide the door handle back and pull it off
    • Pull the cables out of the door handle
  4. step : Installing the New Door Handle (4:24)
    • Turn the new door handle upside down
    • Put the top cable into the lower clip (still holding the handle upside down)
    • Put the bottom cable into the lower clip (still holding the handle upside down)
    • Turn the handle right side up
    • Push the door handle into place
  5. step : Reinstalling the Door Panel (5:07)
    • Put the door panel into place, pulling the wiring harnesses through their cavities
    • Push the door panel clips in
    • Push on the mirror base trim panel
    • Push the door handle bezel in
    • Connect the window switch wiring harness
    • Push in the window switch panel
    • Connect the courtesy light wiring harness
    • Push in the courtesy light
    • Insert the Phillips screw below the door pull
    • Insert the Phillips screw into the door handle
    • Insert the Phillips screw at the top front corner of the door panel
    • Push in the screw cover below the door pull
    • Push in the screw cover into the door handle
    • Push in the screw cover at the top front corner of the door panel
    • Push the clips into the back of the door panel
  6. step : Reconnecting the Battery (6:55)
    • Reconnect the negative battery cable

Tools needed for replacement:

    General Tools

  • Putty Knife

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Specialty Tools

  • Door Panel Removal Tool

  • Wrenches - Metric

  • 8mm Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
2001-2007Toyota Sequoia Toyota Sequoia Front & Rear Interior Door Handle & Bezel Kit 8 Piece Set
2004-2006Toyota Tundra Toyota Tundra Crew Cab Front & Rear Interior Door Handle & Bezel Kit 8 Piece Set

Part Interchange

Brand Label Part Number
DIY Solutions BHS03287
DIY Solutions BHS02069
DIY Solutions BHS02070
DIY Solutions BHS01753
DIY Solutions BHS01752

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: DHA37270
Product Reviews
5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Excellent
Parts were excellent, ordering was easy, price was great and delivery was timely.
April 10, 2019
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Toyota Sequoia Tundra Front & Rear Interior Door Handle & Bezel Kit 8 Piece Set TRQ-1ADHS01701 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.