Toyota Prius Prius Plug-In Wheel Bearing & Hub Assembly TRQ BHA54386 - 1ASHR00307

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
      Direct Fit Replacement
      Precision Engineered
      Highest Quality Materials
  • Bearing Type:   Ball Bearing


Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Battery (0:25)
    • Disconnect the negative battery terminal with a 10mm wrench
  2. step : Removing the Wheel (1:00)
    • Pry off the hub cap with a pry bar
    • Loosen the lug nuts with a 21mm socket and breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts by hand
    • Pull the wheel off the studs
  3. step : Removing the Brake Parts (1:58)
    • Remove the parking brake cable from the retainer with needle nose pliers
    • Loosen the two slide bolts from the caliper with a 14mm wrench and a dead blow hammer
    • Swing the caliper around and off the brake pads
    • Secure the caliper with a bungee cord
    • Remove the brake pad clips
    • Remove the brake pads from the caliper bracket with a flat blade screwdriver
    • Remove the two 14mm bolts from the caliper bracket with a wrench
    • Pull the caliper bracket off the wheel knuckle
    • Pry open the ABS sensor cover with a flat blade screwdriver
    • Disconnect the ABS sensor
  4. step : Removing the Hub (7:26)
    • Remove the four 14mm bolts from the wheel bearing
    • Pull the hub out
    • Tap the hub out with a rubber mallet if needed
  5. step : Installing the Hub (10:05)
    • Clean off the mating surface with rust penetrant and a wire brush
    • Insert the hub into place
    • Torque the bolts between 66 foot-pounds
    • Reconnect the ABS sensor and close the cover
  6. step : Preparing the Brake Parts (14:24)
    • Clean the caliper bracket with brake parts cleaner and a wire brush
    • Clean the brake pad clips with brake parts cleaner and a wire brush
    • Clean and grease the brake caliper slides with brake parts cleaner and brake grease
  7. step : Installing the Brake Rotor (20:27)
    • Slide the rotor backwards onto the hub
    • Spray the rotor with brake parts cleaner and a rag
    • Slide the rotor onto the hub
    • Fasten one lug nut onto a stud to hold the rotor in place
    • Spray the front of the rotor with brake parts cleaner and a rag
  8. step : Installing the Brake Pads (21:42)
    • Line up the caliper with the caliper bracket
    • Line up the caliper bracket on the wheel
    • Start the 19mm bolts for the caliper bracket
    • Torque the caliper bracket bolts to 42 foot-pounds
    • Clean the brake pads padding with brake parts cleaner
    • Apply caliper grease to the brake pad ears
    • Place the brake pads into the caliper bracket
    • Replace the brake pad clips
    • Pull the bungee cord off the brake caliper
    • Compress the caliper piston with needle nose pliers
    • Swing the caliper onto the caliper bracket
    • Insert the slide bolts into the caliper
    • Insert the brake cable into the retainer with needle nose pliers
    • Torque the slide bolts to 25 foot-pounds
    • Remove the lug nut from the brake rotor
  9. step : Installing the Wheel (27:11)
    • Slide the wheel onto the studs
    • Start the lug nuts by hand
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds
    • Pump the brake pedal until the brakes feel firm
  10. step : Reconnecting the Battery ()
    • Connect the negative battery terminal with a 10mm wrench

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner
  • Paper Towels
  • Anti-Seize Grease
  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 19mm Socket
  • 21mm Socket
  • 10mm Socket

  • Specialty Tools

  • Dead Blow Hammer

  • Wrenches - Metric

  • 14mm Wrench
  • 17mm Wrench
  • 19mm Wrench
  • 10mm Wrench

4.50/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Great item
It can quickly. I would recommend renting a hub puller and the night before using a penetrating spray. It was really stuck.
September 20, 2017
I am just happy to find a part I need that is affordable. This same part, just the part, my Toyota dealer from where I bought my Prius would have cost me $315.00 and this did not include the labor. So in the end I did the repair myself and saved a lot of money.
November 3, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2010-2016Toyota Prius Toyota Prius Rear Wheel Bearing & Hub Assembly Driver or Passenger Side TRQ
2012-2015Toyota Prius Plug-In Toyota Prius Plug-In Rear Wheel Bearing & Hub Assembly Driver or Passenger Side TRQ
Part #: 1ASHR00307

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: BHA54386

How-to Video:

(28:51 min)