1ASTB00048-Toyota Lexus Pontiac Driver or Passenger Side Steering Rack & Pinion Bellow

Replaces

Toyota Lexus Pontiac Driver or Passenger Side Steering Rack & Pinion Bellow EMPI

1ASTB00048

This part replaces:

  • Beck Arnley 103-3068
  • EMPI 88-1631-K
FREE SAME DAY SHIPPING
Save 30%
List: $32.95 Save: $10.00
Part 1ASTB00048
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

EMPI
Brand #: 88-1631-K
Description
Vehicle Fit
Warranty & Shipping
How-To & Tools

Specifications:

  • Brand New Rack & Pinion Bellow
  • Fits LH (Driver Side) or RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (0:24)
    • Pry off the hub cap with a pry bar
    • Loosen the lug nuts with a 21mm socket and breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull the wheel off the hub
  2. step : Removing the Ball Joint (1:12)
    • Apply rust penetrant to the ball joint nuts and bolt
    • Loosen the two ball joint nuts with a 17mm socket and breaker bar
    • Loosen the ball joint bolt with a 17mm socket and breaker bar
    • Remove the cotter pin from the ball joint castle nut with needle nose pliers and side cutters
    • Drive the cotter pin out of the castle nut with a hammer and punch
    • Loosen the castle nut with a 19mm wrench and a dead blow hammer
    • Strike the wheel knuckle with a small sledge hammer
    • Remove the two 17mm nuts from the ball joint
    • Remove the 17mm bolt from the ball joint
    • Separate the ball joint from the control arm
    • Pry the ball joint out of the wheel knuckle with a pry bar
    • Remove the castle nut from the ball joint
    • Pull the ball joint out of the wheel knuckle
  3. step : Installing the Ball Joint (6:42)
    • Remove the cotter pin and castle nut from the new ball joint
    • Clean any grease from the wheel knuckle
    • Slide the ball joint into the wheel knuckle
    • Start the castle nut onto the ball joint by hand
    • Slide the ball joint studs into the control arm
    • Start the two 19mm nuts onto the ball joint studs by hand
    • Start the 17mm bolt into the control arm
    • Tighten the castle nut with a 19mm wrench
    • Line up the castle nut with the cotter pin hole
    • Insert the cotter pin into its hole
    • Fold over the cotter pin with pliers
    • Tighten the 17mm bolt
    • Tighten the two 19mm nuts to 55 foot-pounds of torque
  4. step : Installing the Wheel (9:32)
    • Slide the wheel onto the hub
    • Start the lug nuts with the tapered side facing the wheel
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds in a star pattern
    • Line up the hub cap with the valve stem
    • Push the hub cap onto the wheel
    • Pump the brake pedal until it feels firm

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Rubber Mallet
  • Sledge Hammer
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Cloth Rags

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Dead Blow Hammer

  • Wrenches - Metric

  • 19mm Wrench


Fits the following Makes:

Year Make Model Description
2007-2012Lexus ES350 Lexus ES350 Front Driver or Passenger Side Steering Rack & Pinion Bellow
2003-2009Lexus GX470 Lexus GX470 Driver or Passenger Side Steering Rack & Pinion Bellow
2010-2013Lexus RX350 Lexus RX350 (US Built Models) Front Driver or Passenger Side Steering Rack & Pinion Bellow
2003-2008Pontiac Vibe Pontiac Vibe Front Driver or Passenger Side Steering Rack & Pinion Bellow
2003-2009Toyota 4Runner Toyota 4Runner Front Driver or Passenger Side Steering Rack & Pinion Bellow
2007-2013Toyota Camry Toyota Camry Front Driver or Passenger Side Steering Rack & Pinion Bellow
2003-2008Toyota Corolla Toyota Corolla Front Driver or Passenger Side Steering Rack & Pinion Bellow
2003-2008Toyota Matrix Toyota Matrix Front Driver or Passenger Side Steering Rack & Pinion Bellow
2009-2013Toyota Venza Toyota Venza Front Driver or Passenger Side Steering Rack & Pinion Bellow

Part Interchange

Brand Label Part Number
Beck / Arnley 103-3068
Beck/Arnley 103-3068
DIY Solutions SUS07221

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
EMPI
Brand #: 88-1631-K
Product Reviews
There are no reviews for this item.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Toyota Lexus Pontiac Driver or Passenger Side Steering Rack & Pinion Bellow EMPI-1ASTB00048 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.