MNSTS00070-Toyota Lexus Front Driver Side Strut & Spring Assembly

Replaces

Toyota Lexus Front Driver Side Strut & Spring Assembly Monroe Quick-Strut 271679

MNSTS00070

This part replaces:

  • Hollander 527-59319AL
FREE SAME DAY SHIPPING
Save 39%
List: $252.95 Save: $99.00
Only 1 left in stock
Part MNSTS00070
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Monroe Quick-Strut
Brand #: 271679

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

Why Buy Monroe Quick-Strut Assemblies?

Monroe Quick-Strut assemblies are high quality and easy-to-install. Some of its benefits include:

  • Application specific technology
  • Restores factory ride height and feel
  • Quicker installation time than bare strut assemblies
  • Pre-assembled and no compression tool required
    • Includes new mount, bearing, coil spring, isolators, boot, and strut
  • Nitrogen gas charged

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (0:37)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Pull off the hub cap
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Strut (3:27)
    • Hold the sway bar link collar with vise grips
    • Remove the 14mm nut from the top of the sway bar link
    • Remove the vise grips
    • Pull the sway bar out of the strut
    • Remove the ABS sensor wire from the clip
    • Remove the 12mm bolt from the ABS sensor
    • Pull the sensor and brake line aside
    • Loosen the two 22mm nuts at the bottom of the strut
    • Tap the 22mm bolts loose with a hammer
    • Remove the 22mm nuts and bolts
    • Open the hood
    • Remove two of the three 14mm nuts from the top of the strut
    • Loosen the third 14mm nut
    • Support the strut as you remove the last 14mm nut
    • Pull the strut down and out
  3. step : Installing the Strut (7:52)
    • Lift the strut into place
    • Start the three 15mm nuts onto the bolts at the top of the strut
    • Tighten the 15mm nuts to 59 foot-pounds of torque
    • Make sure the steering wheel is straight
    • Line the spindle up with the strut
    • Place the two 22mm bolts into the bottom of the strut
    • Start the two 22mm nuts onto the bolts at the rear
    • Hold the nuts with a 22mm wrench
    • Tighten the bolts with a 22mm socket and ratchet
    • Tighten the 22mm nuts to 156 foot-pounds
    • Clip the brake line and abs wire into place
    • Insert the 12mm bolt into the ABS sensor bracket
    • Push the ABS sensor clip onto the wheel spindle
    • Fasten vice grips to the sway bar link collar
    • Put the sway bar link into the strut
    • Start the 14mm nut onto the sway bar link
    • Tighten the 14mm nut to 29 foot-pounds
    • Remove the vice grips
  4. step : Reattaching the Wheel (10:34)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 21mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 22mm Socket
  • 14mm Socket
  • 15mm Socket
  • 12mm Socket
  • 21mm Socket

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
1997-2001Lexus ES300 Lexus ES300 Front Driver Side Strut & Spring Assembly
1997-2003Toyota Avalon Toyota Avalon Front Driver Side Strut & Spring Assembly
1997-2001Toyota Camry Toyota Camry V6 3.0L Front Driver Side Strut & Spring Assembly
1999-2003Toyota Solara Toyota Solara V6 3.0L Front Driver Side Strut & Spring Assembly

Part Interchange

Brand Label Part Number
DIY Solutions SHO03961

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
Monroe Quick-Strut
Brand #: 271679
Product Reviews
There are no reviews for this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Toyota Lexus Front Driver Side Strut & Spring Assembly Monroe Quick-Strut 271679-MNSTS00070 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.