Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

Our axles are NEW. They are made to the same OEM specifications out of high strength alloy.


  • Comes as a PAIR
    • Fits LH (Driver Side) and RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 43410-06161-84, 43410-06161, 43420-06160, 434100616184, 4341006161, 4342006160
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:29)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack near the pinch weld
    • Secure the vehicle on jack stands at the unibody frame rail, and place it just ahead of the lower control arm on the rear
    • Repeat the process for the other side so the vehicle is level
    • Remove the hub cap
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Axle Nut (3:05)
    • Bend the cotter pin down with needle nose pliers
    • Pull the cotter pin up and out
    • Remove the lock cover on the nut
    • Hold the hub still with a pry bar
    • Break the axle nut socket loose with a 32mm socket and breaker bar
    • Leave the nut at the end of the axle
    • Hammer the axle out
    • Remove the axle nut
  3. step : Removing the CV Axle from the Spindle (4:24)
    • Remove the 12mm bolt retaining the ABS wire
    • Remove the line out of the way
    • Break the 22mm strut nuts loose and remove them
    • Tap the bolts out of the spindle with a punch and hammer
    • Pull the spindle down and out of the strut
    • Pull the axle out of the spindle
  4. step : Removing the CV Axle from the Differential (6:07)
    • Have a drain pan ready
    • Insert two pry bars to 3 and 9 o'clock on the axle
    • Carefully work the snap ring out of its holder inside the differential
    • Remove the axle from the differential
  5. step : Installing the CV Axle to the Differential (8:30)
    • Lubricate the inboard joint on the axle with transmission fluid
    • Align the axle splines with the splines in the differential
    • Work the axle into the differential
  6. step : Inserting the CV Axle to the Spindle (9:06)
    • Line up the splines into the hub
    • Start the axle nut on the end of the axle
    • Reinstall the 22mm strut bolts to the spindle
    • Tap the bolts into place with a hammer if needed
    • Tighten the nuts to 156 foot-pounds
    • Snap the ABS retainer into place
    • Tighten the 12mm bolt to the ABS wire
  7. step : Installing the Axle Nut (10:52)
    • Tighten down the axle nut with a 32mm socket and ratchet
  8. step : Reinstalling the Wheel (10:58)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to partial weight the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Lower the jack
    • Torque the axle to 217 foot-pounds
    • Reinstall the lock cap and new cotter pint to the axle nut
    • Reinstall your hubcap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Drain Pan
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 32mm Socket
  • 22mm Socket
  • 12mm Socket
  • 21mm Socket

4.8 / 5.0
4 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
best bang for your buck
product was straight forward to install, it works well, and has lifetime warranty.
But.. the only problem I had was that axle nuts provided where different sizes.
August 4, 2017
9 months ago
Good cv's
After a month so far so good went right on my 95 Camry
October 25, 2017
7 months ago
The absolute best
A friend of mines recommend this site to me and at first I'm like no way those parts are that cheap, but the kicker is they are actually brand new products for a very affordable price which is amazing. Shipping came very very fast and all my pieces were there. I would certainly give this place an A-1 rating and most certainly will be ordering again!
April 8, 2018
1 month ago
Cv axles 95 Camry 2.2
Parts fit well, however, the input shaft dust shields were bent in shipping and they did not come with new cotter pins
March 4, 2017
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Brand name of part I'm ordering?
Levi M on Apr 22, 2016
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle and are covered by a lifetime warranty. If you have any further questions, please don't hesitate to ask.

Vehicle Fit

  • 1992-2001 Toyota Camry Pair L4 2.2L CV Axle Shaft
  • 1999-2001 Toyota Solara Pair L4 2.2L CV Axle Shaft
Part #: 1AACS00078

How-to Video:

(12:24 min)