Replaces

Toyota Avalon Camry Lexus ES300 Rear Passenger Side Strut & Spring Assembly TRQ

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (1:14)
    • Pull off the hub cap by hand
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Strut (1:37)
    • Remove the 12mm bolt from the brake line
    • Remove the 10mm bolt from the ABS sensor
    • Pull the brake line off the strut
    • Pull the ABS sensor off the strut
    • Attach locking pliers to the upper sway bar ball joint
    • Remove the lower sway bar link nut with a 14mm socket and ratchet
    • Remove the sway bar link from the strut
    • Remove the two 19mm nuts and bolts that connect the strut to the wheel spindle
    • Lift the rear seat off its ancho points
    • Push the seat belts through the rear seat cushion
    • Pull the rear seat out through the door
    • Remove the 12mm bolt from each rear seat bolster
    • Pull out the rear seat bolsters
    • Pull the seatbelt aside
    • Pull back the sound-deadening material
    • Remove the three 12mm bolts from the top of the strut
    • Pull the strut down and out
  3. step : Installing the Strut (5:44)
    • Lift the strut into place, lining up the studs
    • Start the 13mm nuts onto the strut mount
    • Insert the 19mm bolts that connect the strut to the wheel spindle
    • Start the 19mm nuts onto the bolts
    • Tighten the 19mm nuts to 83 foot-pounds of torque
    • Put the ABS sensor bracket into place
    • Insert the 10mm bolt into the ABS sensor bracket
    • Put the brake line into place
    • Insert the 12mm bolt into the brake line bracket
    • Put the sway bar link into place
    • Attach locking pliers to the upper sway bar ball joint
    • Fasten the 14mm nut onto the sway bar link
  4. step : Reattaching the Wheel (7:31)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  5. step : Securing the Strut and Reinstalling the Rear Seat (8:08)
    • Fasten the three 13mm nuts onto the strut mount
    • Push the rear seat bolsters into place using the locating tabs
    • Insert the 12mm bolt into each rear seat bolster bracket
    • Push the rear seat cushion into place
    • Pull the seatbelts through the rear seat cushion
    • Pop in the seat cushion clips

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 14mm Socket
  • 12mm Socket
  • 13mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 14mm Wrench
  • 19mm Wrench
  • 10mm Wrench
  • 13mm Wrench
  • 12mm Wrench

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Great price, perfect fit, what more could you want!!!!!!!!!!
March 19, 2017
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
1992-1994Lexus ES300 Lexus ES300 Rear Passenger Side Strut & Spring Assembly
1997-2001Lexus ES300 Lexus ES300 without Electronic Suspension Rear Passenger Side Strut & Spring Assembly
1997-2003Toyota Avalon Toyota Avalon Rear Passenger Side Strut & Spring Assembly
1992-1994Toyota Camry Toyota Camry V6 3.0L Rear Passenger Side Strut & Spring Assembly
1997-2001Toyota Camry Toyota Camry V6 3.0L Rear Passenger Side Strut & Spring Assembly

Part Interchange

Brand Label Part Number
Monroe 281680
Monroe 271680
Monroe Shocks & Struts 271680
Monroe Shocks & Struts 281680

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Part 1ASTS00529
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: SCA57444