Replaces
Tie Rod - 1ASFK02894
1ASFK02894
Part Details
- Quantity: 4 Piece Set
Specifications:
- Brand New Tie Rods
- Comes as a Set of 4
- Fits LH (Driver Side) & RH (Passenger Side)
- Direct replacement
- Built to strict quality control standards
Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.
Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards. Failure to do so may result in issues with steering and premature tire wear.
Item Condition:
New
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.
-
step : Removing the Wheel (0:52)
- Loosen the lug nuts with the vehicle on the ground
- Remove the hubcap
- Raise the vehicle with a floor jack
- Secure the vehicle on jack stands
- Remove the lug nuts
- Pull off the wheel
-
step : Removing the Outer Tie Rod (1:12)
- Measure from the end of the tie rod boot to the end of the tie rod
- Spray the 22mm nut on the outer tie rod with penetrating oil
- Hold the inner tire rod with a 13mm wrench
- Loosen the nut on the outer tie rod with a 22mm wrench
- Remove the cotter pin from the ball joint nut with pliers
- Remove the 17mm nut from the ball joint
- Hit the spindle with a hammer to knock the ball joint free
- Spin the outer tie rod free
-
step : Installing the New Outer Tie Rod (3:00)
- Screw the grease fitting on the bottom of the new tie rod
- Tighten it with a 7mm socket
- Twist the outer tie rod into the inner tie rod
- Measure from the outside of the boot to the inside of the tie rod to match your previous measurement
- Hold the outer tie rod with a wrench while tightening the 22mm nut to the tie rod
- Attach a grease gun to the ball joint fitting and give it several pumps
-
step : Reattaching the Wheel (4:42)
- Slide the wheel into place
- Replace the hub cap
- Start the lug nuts by hand
- Tighten the lug nuts preliminarily
- Lower the vehicle to the ground
- Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern
After completing this repair, it's recommended to have your car aligned
Tools needed for replacement:
- Hammer
- Jack Stands
- Floor Jack
- Bearing Grease
- Rust Penetrant
- Adjustable Wrench
- Needle nose pliers
- Torque Wrench
- A Piece of Pipe (for leverage)
- Ratchet
- 22mm Socket
- 7mm Socket
- 17mm Socket
- Grease Gun
- 13mm Wrench
- 22mm Wrench
General Tools
Materials, Fluids, and Supplies
Pliers, Cutters & misc Wrenches
Ratchets & Related
Sockets - Metric
Specialty Tools
Wrenches - Metric
Vehicle Fit
| Year | Make | Model | Description |
|---|---|---|---|
| 2001-2006 | Hyundai | Elantra | Hyundai Elantra Inner & Outer Tie Rod 4 Piece Set |
| 2003-2008 | Hyundai | Tiburon | Hyundai Tiburon Inner & Outer Tie Rod 4 Piece Set |
| 2005-2009 | Kia | Spectra | Kia Spectra Inner & Outer Tie Rod 4 Piece Set |
| 2005-2009 | Kia | Spectra 5 | Kia Spectra 5 Inner & Outer Tie Rod 4 Piece Set |
This part replaces:
- Moog ES3377
- Moog EV80310
- OE # 577242D000
- OE # 577242F000
- OE # 56820-22000
