Specifications:

  • Brand New Suspension Kit 
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Quantity: 10 Piece Set
  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Lower Control Arms
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:24)
    • Pry off the hub cap with a pry bar
    • Loosen the lug nuts with a 21mm socket and breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull the wheel off the hub
  2. step : Removing the Ball Joint (1:12)
    • Apply rust penetrant to the ball joint nuts and bolt
    • Loosen the two ball joint nuts with a 17mm socket and breaker bar
    • Loosen the ball joint bolt with a 17mm socket and breaker bar
    • Remove the cotter pin from the ball joint castle nut with needle nose pliers and side cutters
    • Drive the cotter pin out of the castle nut with a hammer and punch
    • Loosen the castle nut with a 19mm wrench and a dead blow hammer
    • Strike the wheel knuckle with a small sledge hammer
    • Remove the two 17mm nuts from the ball joint
    • Remove the 17mm bolt from the ball joint
    • Separate the ball joint from the control arm
    • Pry the ball joint out of the wheel knuckle with a pry bar
    • Remove the castle nut from the ball joint
    • Pull the ball joint out of the wheel knuckle
  3. step : Installing the Ball Joint (6:42)
    • Remove the cotter pin and castle nut from the new ball joint
    • Clean any grease from the wheel knuckle
    • Slide the ball joint into the wheel knuckle
    • Start the castle nut onto the ball joint by hand
    • Slide the ball joint studs into the control arm
    • Start the two 19mm nuts onto the ball joint studs by hand
    • Start the 17mm bolt into the control arm
    • Tighten the castle nut with a 19mm wrench
    • Line up the castle nut with the cotter pin hole
    • Insert the cotter pin into its hole
    • Fold over the cotter pin with pliers
    • Tighten the 17mm bolt
    • Tighten the two 19mm nuts to 55 foot-pounds of torque
  4. step : Installing the Wheel (9:32)
    • Slide the wheel onto the hub
    • Start the lug nuts with the tapered side facing the wheel
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds in a star pattern
    • Line up the hub cap with the valve stem
    • Push the hub cap onto the wheel
    • Pump the brake pedal until it feels firm

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Rubber Mallet
  • Sledge Hammer
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Cloth Rags

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Dead Blow Hammer

  • Wrenches - Metric

  • 19mm Wrench

4.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
1
0
0
0
2000 Corolla 10 pc front suspension kit
My name's Mark and this is the first time I've purchased anything from 1A Auto and parts arrived very quickly with free shipping. It took me about a week to get around to installing the parts and everything installed quickly and easily aside from a hiccup I encountered when removing the control arm pivot bolt from the drivers side. The pivot bolt runs directly into the transmission oil pan so I had to remove some motor mount bolts in order to have the pivot bolt slide out freely while the transmission was raised a bit. The how to video that was included for these parts on the website was for a Toyota Camry which is a bit different for removing these parts and installing. It would be ideal if the how to video showed the vehicle that the parts were for but it's understandable how the video was a generic type for vehicles similar to mine as it would probably be quite difficult for 1A Auto to provide a how to video on every single part for each vehicle part they sell. I give 4 stars for there dedication to Auto doit yourselfers like me!! I would recommend their parts and services for all of my friends and family. Reliable, inexpensive, quality parts to get the job done and good warranties to protect the money you spend. -Mark Cleburne, TX
May 5, 2018
Purchased
3 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 5 answers
Who manufactures these parts?
Taylor P on Sep 4, 2016
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. If you have any further questions, please don't hesitate to ask.
Does this set come with bushing also?
Kaiks on Dec 28, 2016
BEST ANSWER: absolutely, we will ship you the most complete kit shown here with the bushings all pre-pressed for a pain free installation

Vehicle Fit

  • 1998-2002 Chevy Prizm 10 Piece Set Suspension Kit
  • 1996-1997 Geo Prizm 10 Piece Set Suspension Kit
  • 1996-2002 Toyota Corolla 10 Piece Set Suspension Kit

This part replaces:

  • Moog EV303
  • Moog K90309
  • Moog K90124
  • Moog ES2382
  • Moog K80336
  • Moog K80335
  • Dorman 520-417
  • Dorman 520-418
  • Hollander 512-58478BL
  • Hollander 512-58478BR
  • Hollander K9756
  • OE # 4504619175, 4504629305
  • OE # 4550329365, 4550319215
  • OE # 4333009230, 4333019115
  • OE # 48069-02010, 12171, 12180
  • OE # 48068-02010, 12171, 12180
  • OE # 48820-33010
Part #: 1ASFK01670

How-to Video:

(11:14 min)