Specifications:

  • Brand New Steering and Suspension Kit
  • Comes as a 14 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Clean up the top of the upper control arm (1:00)
  2. step : Install the ball joint (1:07)
    • Line up the boot on the ball joint and put the ball joint in place and put the nut on it.
    • Bolt the ball joint in with the four nuts and bolts.
    • Torque them to 25 ft lbs
  3. step : Install the tie rod. (2:18)
    • Put the tie rod in place
    • Bolt it in at 55 ft lbs.
    • Put in the cotter pin, hammer it through and bend it with a pair of pliers.
    • Fill the tie rod end with grease.
  4. step : Install the hub (3:35)
    • Put the O ring into the hub.
    • Mount the hub and thread the ABS harness into place.
    • Bolt the hub into place and make sure the shield is in the correct position.
    • Use a star like pattern when bolting in the hub and torque the bolts to 65 ft lbs.
    • Clip and bolt the ABS harness in and connect it.
  5. step : Install the brakes (6:05)
    • Mount the rotor and caliper
    • Bolt the caliper bolts in and torque to 50-60 ft lbs.
    • Use a rubber mallet to help get the caliper on.
  6. step : Install the hub nut and wheel. (7:00)
    • Before putting the wheel on, put the hub nut on and tighten but do not torque.
    • Put the wheel back on and lower the car.
    • Torque the hub nut to 90 ft lbs.
    • Using a star pattern, torque the wheel lug nuts to 75 ft lbs.
    • Put the cap and lug nut covers on.

Tools needed for replacement:

    General Tools

  • Chisel
  • Floor Jack
  • Hammer
  • Jack Stands
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 11mm Socket
  • 12mm Socket
  • 13mm Socket
  • 14mm Socket
  • 15mm Socket
  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 20mm Socket
  • 21mm Socket
  • 22mm Socket
  • 24mm Socket
  • 35mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 13mm Wrench
  • 18mm Wrench

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
0
0
0
Suspension kit
Loved the kit joints are greaseable and the zerks were in the kit.
Quick delivery price was right. No problems with the fit. Alignment required after install have recommended to friends.
April 22, 2017
Purchased
over 3 years ago
Not installed yet
Hane not installed yet will do that this week. But purchase and delivery went great.
August 20, 2017
Purchased
9 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 10 answers
Will this fit a 2001 ZR2 Blazer?
Zane C on Aug 16, 2016
BEST ANSWER: Yes, according to the information you supplied, the part you’re looking at will be correct for your vehicle. If you have any other questions or would like to place an order with one of our customer service representatives, please feel free to give us a call.
Are the uppet and lower ball joints greasable?
Mini24 on Sep 15, 2015
BEST ANSWER: yes they both have a part with threads and a grease fitting. I did not install the ball joints but the steering parts all worked great. I recommend the kit

Vehicle Fit

  • 1998 Chevy Blazer S10 4 Wheel Drive 14 Piece Set Suspension Kit for Models with Offset Tie Rod
  • 1999-2005 Chevy Blazer S10 4 Wheel Drive 14 Piece Set Suspension Kit
  • 1998 Chevy S10 Pickup 4 Wheel Drive 14 Piece Set Suspension Kit for Models with Offset Tie Rod
  • 1999-2004 Chevy S10 Pickup 4 Wheel Drive 14 Piece Set Suspension Kit
  • 1998 GMC Jimmy S-15 4 Wheel Drive 14 Piece Set Suspension Kit for Models with Offset Tie Rod
  • 1999-2001 GMC Jimmy S-15 4 Wheel Drive 14 Piece Set Suspension Kit
  • 1999-2004 GMC S-15 Sonoma 4 Wheel Drive 14 Piece Set Suspension Kit
  • 1998 Isuzu Hombre 4 Wheel Drive 14 Piece Set Suspension Kit for Models with Offset Tie Rod
  • 1999-2000 Isuzu Hombre 4 Wheel Drive 14 Piece Set Suspension Kit
  • 1999-2001 Olds Bravada 4 Wheel Drive 14 Piece Set Suspension Kit

This part replaces:

  • OE # 8260485610
  • OE # 26048561, 7839709, 8260485610
  • OE # 26054968
  • OE # 12471301
  • OE # 12471300
  • Moog K5335
  • Moog K6251
  • Moog ES2004S
  • Moog K5320
  • Moog K6600
  • Moog K6255
  • Moog ES3462
  • Moog ES3584
Part #: 1ASFK00995


How-to Video:

(09:04 min)