Subaru Passenger Side Power Window Motor Dorman 742-816

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

step : Removing the Door Panel (0:25)

• Pry out the trim door behind the door handle
• Pry off the door pull
• Remove the Phillips screw from the door pull
• Remove the Phillips screw from the door handle
• Pry out the door panel with a trim tool
• Lift the door panel off
• Disconnect the electrical connector
• Disconnect the cables from the door handle

step : Removing the Mirror (3:35)

• Disconnect the wiring harness
• Pry off the cover with a flat blade screwdriver
• Remove the three 8mm bolts from the mirror
• Remove the mirror

step : Removing the Speaker (5:05)

• Remove the Phillips screws from the upper speaker
• Disconnect the wiring harnesses from both speakers
• Remove the Phillips screws from the door speaker
• Remove the speaker
• Pry off the harnesses with a trim tool

step : Removing the Window Glass (6:25)

• Peel off the water vapor barrier
• Pry off the lower panel with a flat blade screwdriver
• Remove the two 10mm bolts from the inside of the door below the mirror mount
• Remove the two 10mm bolts from the exterior of the door below the mirror mount
• Lift the sail corner up and out
• Remove the two 10mm bolts from the window guide
• Pry up the window guide
• Remove the metal window guide clips from the door
• Plug in the window switch
• Turn the key to the ON position
• Lower the window down slowly
• Disconnect the window switch
• Remove the 10mm nuts from the window
• Lift the window up and out

step : Removing the Window Regulator (12:22)

• Disconnect the window regulator connector
• Remove all but one of the 10mm bolts from the regulator
• Slide the regulator down and out

step : Removing the Window Motor (13:33)

• Secure the metal gear to the bracket with locking pliers as the regulator is spring loaded
• Remove the Phillips screws from the window motor
• Keeping your fingers clear, gently pry the motor from the regulator with a flat blade screwdriver

step : Installing the Window Motor (15:48)

• Apply white lithium grease to the motor gear
• Insert the motor to the regulator
• Tighten the 10mm bolts to the regulator
• Release the locking pliers
• Apply white lithium grease to the gear teeth and regulator tracks

step : Installing the Window Regulator (17:26)

• Hand-tighten a bolt to the regulator
• Insert the regulator into the door and hang it by its bolt
• Tighten the 10mm bolts to the regulator
• Connect the electrical connector

step : Installing the Window Glass (19:07)

• Insert the window into place
• Tighten the 10mm bolts to the window
• Connect the window switch
• Insert the metal window guide clips to the door
• Insert the window guide into place
• Insert the metal corner panel into place
• Tighten the four 10mm bolts to the metal corner panel
• Replace the vapor barrier

step : Installing the Speaker (27:10)

• Insert the speaker into place
• Tighten the Phillips screws to the speaker
• Connect the wiring harness
• Insert the upper speaker into place
• Tighten the Phillips screw to the speaker
• Connect the wiring harness

step : Installing the Mirror (28:30)

• Insert the mirror into place
• Tighten the 10mm bolts to the mirror
• Connect the wiring harness

step : Installing the Door Panel (30:03)

• Connect the cables to the door handle
• Connect the electrical connector
• Lift the door panel on
• Tighten the Phillips screw to the door handle
• Tighten the Phillips screw to the door pull
• Press on the door pull trim
• Press on the door handle trim