Replaces

Strut & Spring Assembly Rear Passenger Side - 1ASTS00529

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Pre-assembled, loaded strut & spring assemblies allow for a quicker, safer install than replacing with just bare struts. 

Trouble-Free Install

Trouble-free install includes the matched parts needed to get the job done. New mounts, bearings, springs and hardware will provide a better ride for your vehicle and save you time from not having to do the job again because a used part failed afterwards.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:14)
    • Pull off the hub cap by hand
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Strut (1:37)
    • Remove the 12mm bolt from the brake line
    • Remove the 10mm bolt from the ABS sensor
    • Pull the brake line off the strut
    • Pull the ABS sensor off the strut
    • Attach locking pliers to the upper sway bar ball joint
    • Remove the lower sway bar link nut with a 14mm socket and ratchet
    • Remove the sway bar link from the strut
    • Remove the two 19mm nuts and bolts that connect the strut to the wheel spindle
    • Lift the rear seat off its ancho points
    • Push the seat belts through the rear seat cushion
    • Pull the rear seat out through the door
    • Remove the 12mm bolt from each rear seat bolster
    • Pull out the rear seat bolsters
    • Pull the seatbelt aside
    • Pull back the sound-deadening material
    • Remove the three 12mm bolts from the top of the strut
    • Pull the strut down and out
  3. step : Installing the Strut (5:44)
    • Lift the strut into place, lining up the studs
    • Start the 13mm nuts onto the strut mount
    • Insert the 19mm bolts that connect the strut to the wheel spindle
    • Start the 19mm nuts onto the bolts
    • Tighten the 19mm nuts to 83 foot-pounds of torque
    • Put the ABS sensor bracket into place
    • Insert the 10mm bolt into the ABS sensor bracket
    • Put the brake line into place
    • Insert the 12mm bolt into the brake line bracket
    • Put the sway bar link into place
    • Attach locking pliers to the upper sway bar ball joint
    • Fasten the 14mm nut onto the sway bar link
  4. step : Reattaching the Wheel (7:31)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  5. step : Securing the Strut and Reinstalling the Rear Seat (8:08)
    • Fasten the three 13mm nuts onto the strut mount
    • Push the rear seat bolsters into place using the locating tabs
    • Insert the 12mm bolt into each rear seat bolster bracket
    • Push the rear seat cushion into place
    • Pull the seatbelts through the rear seat cushion
    • Pop in the seat cushion clips

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 14mm Socket
  • 12mm Socket
  • 13mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 14mm Wrench
  • 19mm Wrench
  • 10mm Wrench
  • 13mm Wrench
  • 12mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Great price, perfect fit, what more could you want!!!!!!!!!!
March 19, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1992-1994 Lexus ES300 Rear Strut & Spring Assembly Passenger Side
  • 1997-2001 Lexus ES300 Rear Strut & Spring Assembly Passenger Side without Electronic Suspension
  • 1997-2003 Toyota Avalon Rear Strut & Spring Assembly Passenger Side
  • 1992-1994 Toyota Camry Rear Strut & Spring Assembly V6 3.0L Models Passenger Side
  • 1997-2001 Toyota Camry Rear Strut & Spring Assembly V6 3.0L Models Passenger Side

This part replaces:

  • Monroe 271680
  • Monroe 281680
Part #: 1ASTS00529


How-to Video:

(09:40 min)