Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Quantity: 4 Piece Set
  • Kit Includes: (2) Front Hub Assemblies

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:42)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Remove the hub cap with pliers
    • Loosen the 13mm nut
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:32)
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove the 13mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (2:32)
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Thread a nut onto the rotor
    • Hit the rotor with a hammer
    • Pull the rotor off
  4. step : Removing the Hub (2:58)
    • Disconnect the ABS harness sensor
    • Remove the ABS from the harness on the bracket
    • Remove the four 18mm bolts from the hub
    • Remove the 13mm hub nut, making sure you can push the nut in and out
    • Twist in an 18mm bolt to the hub
    • Remove the hub
  5. step : Installing the Hub (4:42)
    • Grease the set of bearings inside the new hub with bearing grease
    • Apply a light coat of bearing grease to the engaging wheel for the 4WD
    • Insert the hub into place
    • Tighten the 18mm bolts to the hub
    • Tighten the 18mm bolts to 95 foot-pounds of torque
    • Replace and tighten the 13mm hub nut
    • Tighten the 13mm bolt to 20 foot-pounds of torque
    • Push the ABS wire into its respective brackets
    • Replace the hub cap
  6. step : Installing the New Brake Rotor (6:41)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Adjust the emergency brake, if necessary
    • Put the bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts to 95 foot-pounds of torque
  7. step : Installing the New Brake Pads (7:24)
    • Put the caliper on
    • Thread the 13mm bolts by hand
    • Tighten bolts to 25 foot-pounds
    • Remove the lug nut from the rotor
  8. step : Reattaching the Wheel (8:55)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Connect the ABS sensor
  9. step : Testing the Brakes (9:42)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • A Piece of Pipe (for leverage)
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 21mm Socket
  • 18mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
06 Ford F-150 front hubs
Highly recommended 1 A Auto! They are great! YouTube videos are great, Affordable & fast shipping. Parts are holding up great, streering on the truck is solid. I will always count on 1 A Auto.
April 4, 2018
Purchased
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005 Ford F150 Truck 4 Wheel Drive 6 Lug Wheels (Built After 11/28/04 Production Date) 4 Piece Set Steering Kit
  • 2006-2008 Ford F150 Truck 4 Wheel Drive 6 Lug Wheels 4 Piece Set Steering Kit
  • 2006-2008 Lincoln Mark LT 4 Wheel Drive 4 Piece Set Steering Kit

This part replaces:

  • Moog ES3691
  • Hollander 538-01672
  • OE # 4L3Z3A130CA
  • OE # 7L3Z 1104 A
Part #: 1ASFK05232


Order must be placed by 4pm ET

How-to Video:

(10:13 min)