Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    NOTE: After completing the procedure you will need a professional alignment

  1. step : Removing the Wheel (0:47)
    • Loosen the 22mm caps on the hubcap with the vehicle on the ground
    • Pull the hubcap free
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Upper Control Arm (1:10)
    • Mark the tab on the adjustment piece with a marker to mark the alignment
    • Remove the two 10mm bolts holding the brake line and move the brackets
    • Remove the ball joint nut with an 18mm wrench
    • Hit the wheel knuckle and control arm to break them free
    • Remove the 21mm nuts from the upper control arm bracket
    • Jack up the wheel underneath the wheel knuckle
    • Remove the upper control arm nut
    • Remove the bolts and upper control arm bracket
    • Place a nut back on and use an air hammer to knock the bolt out if it won't budge
    • Move the control arm up and down while pulling out
  3. step : Installing the Upper Control Arm (3:52)
    • Put the upper control arm into place and push the 21mm bolts in to hold it
    • Put the brackets on either side and realign them up
    • Angle the control arm down into the wheel knuckle
    • Replace the 18mm ball joint nut
    • Replace the 21mm nuts from the upper control arm bracket
    • Replace and tighten the two 10mm bolts
    • Put a grease gun into place on the end of the control arm and fill it up
  4. step : Reattaching the Wheel (6:00)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the hubcap and tighten the caps

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 10mm Socket
  • 21mm Socket
  • 22mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 18mm Wrench
  • 21mm wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2006 Chevy Silverado 1500 2 Wheel Drive for Models with Front Torsion Bar Suspension for Models without Rack & Pinion Steering 10 Piece Set Steering Kit
  • 2007 Chevy Silverado 1500 Classic 2 Wheel Drive for Models with Front Torsion Bar Suspension for Models without Rack & Pinion Steering 10 Piece Set Steering Kit
  • 2004-2006 GMC Sierra 1500 2 Wheel Drive for Models with Front Torsion Bar Suspension for Models without Rack & Pinion Steering 10 Piece Set Steering Kit
  • 2007 GMC Sierra 1500 Classic 2 Wheel Drive for Models with Front Torsion Bar Suspension for Models without Rack & Pinion Steering 10 Piece Set Steering Kit

This part replaces:

  • Moog K80942
  • Moog ES3493T
  • Moog K80631
  • Moog ES3488
  • Moog K6539
  • Dorman 520-116
  • Hollander 511-01044
  • OE # 15295861, 26059210
  • OE # 15864153, 12475485, 15047200
  • OE # 19149617
  • OE # 15750786, 15015515
Part #: 1ASFK04737

How-to Video:

(07:07 min)