Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:00)
    • Loosen the lug nuts.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Remove the front shield (1:15)
    • Use a 15 mm socket and ratchet.
    • Remove the four bolts.
  3. step : Remove the Idler Arm (1:25)
    • Remove the 24 mm bolt securing the idler arm to the steering linkage
    • Use a joint fork and a hammer to separate the joint.
    • Remove the three other bolts securing the idler arm.
    • Use a Tie Rod Puller to pull apart the idler arm and the idler shaft.
  4. step : Install the new idler arm (4:34)
    • Assemble your new idler arm to your idler shaft, threading on the bushing and nut.
    • Bolt in the idler arm assembly into place, tightening up the three nuts.
    • Bolt in the end of the idler arm assembly to the steering gear.
    • Torque the nuts and bolts to 80 ft lbs.
    • Install the cotter pin.
    • Use a grease gun and fill the grease fitting.
  5. step : Reassembly (7:25)
    • Replace the shield with the four 15mm bolts.
    • Clip the air bag harness back in.
    • Put the wheel back on and lower the car
    • Using a star pattern torque the lug nuts to 120-140 ft lbs

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 22mm Socket
  • 24mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Fork
  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1995-1999 Chevy K1500 Truck Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 1995-2000 Chevy K2500 Truck 6 Lug Wheels Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 1995-1999 Chevy Suburban K1500 Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 1995-1999 Chevy Tahoe 4 Wheel Drive Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 2000 Chevy Tahoe 4 Wheel Drive V8 5.7L Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 1995-1999 GMC K1500 Truck Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 1995-2000 GMC K2500 Truck 6 Lug Wheels Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 1995-1999 GMC Suburban K1500 Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 1995-1999 GMC Yukon 4 Wheel Drive Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set
  • 2000 GMC Yukon 4 Wheel Drive V8 5.7L Stamped Steel Lower Control Arms Steering & Suspension Kit 16 Piece Set

This part replaces:

  • Moog K6428
  • Monroe SC2942
  • KYB SS10317
  • OE # 12542993
  • OE # 22063969
  • OE # 26048561
  • OE # 26051896
  • OE # 26059031
  • OE # 7839709
  • OE # 8260485610
  • Moog ES2004S
  • Moog ES2836RL
  • Moog ES2838RL
  • Moog K6292
  • Moog K6335
  • Moog K6447
  • Moog K6477
  • Moog K6532
Part #: 1ASFK05771

Out of Stock

How-to Video:

(08:13 min)