Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    It is recommended to seek a professional alignment after completing this repair.

  1. step : Removing the Wheel (0:50)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:08)
    • Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
    • Make note of this measurement
    • Loosen the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Remove the 18mm nut from the outer tie rod end
    • Loosen the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Pull the outer tie rod out of the steering knuckle
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (1:55)
    • Twist the new outer tie rod onto the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Place vise grip pliers to hold the other part of the ball joint
    • Fasten the 18mm nut onto the outer tie rod with a socket
    • Place the pliers on the bottom of the bolt
    • Tighten the nut with an 18mm wrench
    • Tighten the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
    • This should be the same as the measurement noted in Step 2
  4. step : Reattaching the Wheel (3:29)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Measuring Tape
  • Jack Stands
  • Hammer
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Adjustable Wrench

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 18mm Wrench

  • Wrenches - SAE

  • 13/16 Inch Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004 Chevy Malibu New Body Style 4 Piece Set Steering & Suspension Kit
  • 2005-2012 Chevy Malibu 4 Piece Set Steering & Suspension Kit
  • 2004-2007 Chevy Malibu Maxx 4 Piece Set Steering & Suspension Kit
  • 2005-2010 Pontiac G6 4 Piece Set Steering & Suspension Kit
  • 2007-2009 Saturn Aura 4 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog ES800086
  • Moog K620179
  • Moog K620180
  • Dorman 520-163
  • Dorman 520-164
  • Hollander 512-01416L
  • Hollander 512-01415R
  • OE # 22730775
  • OE # 22730776
  • OE # 22687089, 15944090
Part #: 1ASFK05339


How-to Video:

(04:22 min)