Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Bearing Type:   Ball Bearing
  • Quantity:   10 Piece Set
  • Kit Includes:
      (2) Front Outer Tie Rods
      (2) Front Lower Control Arms with Ball Joints
      (2) Front Sway Bar Links
      (2) Front Hub Assemblies
      (2) Front Inner Tie Rods


  • Brand New Steering & Suspension Kit
  • Comes as an 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards


Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Remove the wheel (0:51)
    • Pry off the hub cap.
    • Use your 34 mm socket and breaker bar to loosen the hub nut.
    • Loosen your lug nuts with a 19 mm socket and breaker bar.
    • Raise and secure your vehicle.
    • Remove the lug nuts and set the wheel aside.
  2. step : Remove the brakes (1:31)
    • Use your 15 mm socket to remove the bolts in the caliper bracket.
    • Use a screwdriver to compress the caliper piston.
    • Remove the caliper and tuck it up and out of the way.
    • Pry out the brake pads.
    • Remove two more 15 mm bolts to remove the caliper bracket.
    • Remove the rotor.
  3. step : Remove the Hub (4:11)
    • Hit the hub nut with penetrating oil, and remove it with your 34 mm socket.
    • Give your axle a solid tap with a hammer.
    • Remove the three bolts holding the hub to the steering knuckle.
    • Unplug the ABS sensor.
    • Remove the hub.
  4. step : Install the new hub. (6:58)
    • Plug in the ABS sensor lead.
    • Work the hub onto the axle and start your bolts.
    • Evenly tighten up the bolts, rotating through the three till they are tight enough to torque.
    • Torque the bolts to 60 ft lbs.
    • Put the hub nut on and tighten it preliminarily.
  5. step : Install the brakes (9:46)
    • Inspect your rotors and replace with new ones cleaned with brake parts cleaner if needed.
    • Use a wire brush to clean corrosion from the brake caliper bracket.
    • Bolt the bracket down with a ratchet and 15 mm socket and torque to 80 ft lbs.
    • Apply anti-seize grease to the edges of the brake pads and insert them into the caliper brackets.
    • Compress the calipers with a C-Clamp and mount it.
    • Feed the caliper bolts into place after inspecting and cleaning the bolt sleeves and torque them to 50 ft lbs.
  6. step : Put the wheel back on (13:50)
    • Hand tighten the lug nuts and lower the vehicle.
    • Torque the hub nut to 118 foot pounds.
    • Use a star pattern to torque the lug nuts to 100 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Ratchets & Related

  • Torque Wrench
  • 1/2 Inch Breaker Bar
  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 34mm Socket
  • 19mm Socket
  • 15mm Socket

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
March 7, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2000-2005Buick LeSabre Buick LeSabre 10 Piece Set Steering & Suspension Kit
1998-2005Buick Park Avenue Buick Park Avenue 10 Piece Set Steering & Suspension Kit
1998-1999Buick Riviera Buick Riviera 10 Piece Set Steering & Suspension Kit
2000-2005Cadillac Deville Cadillac Deville 10 Piece Set Steering & Suspension Kit for Models with 5 Lug Wheels
1998-2004Cadillac Seville Cadillac Seville 10 Piece Set Steering & Suspension Kit
1998-1999Oldsmobile Aurora Olds Aurora 10 Piece Set Steering & Suspension Kit
2001-2003Oldsmobile Aurora Olds Aurora 10 Piece Set Steering & Suspension Kit
2000-2003Pontiac Bonneville Pontiac Bonneville 10 Piece Set Steering & Suspension Kit
2004-2005Pontiac Bonneville Pontiac Bonneville 10 Piece Set Steering & Suspension Kit (excluding GXP Models)
Part #: 1ASFK03494

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(14:41 min)